Line 218: |
Line 218: |
| | | |
| === Reject === | | === Reject === |
| + | Takes an input [[#Ipv4Address]], no output. |
| | | |
| === SetAdvertiseData === | | === SetAdvertiseData === |
| + | Takes a type-0x21 input buffer, no output. |
| + | |
| + | The input buffer contains arbitrary user data. |
| | | |
| === SetStationAcceptPolicy === | | === SetStationAcceptPolicy === |
| + | Takes an input [[#AcceptPolicy]], no output. |
| | | |
| === AddAcceptFilterEntry === | | === AddAcceptFilterEntry === |
| + | Takes an input [[#MacAddress]], no output. |
| + | |
| + | There are two sdknso funcs implementing this: one which takes a [[#MacAddress]] directly, the other loads the [[#MacAddress]] from the input [[#NodeInfo]]. |
| | | |
| === ClearAcceptFilter === | | === ClearAcceptFilter === |
Line 235: |
Line 243: |
| | | |
| === Connect === | | === Connect === |
| + | Takes a type-0x19 input buffer containing a [[#NetworkInfo]], a [[#SecurityConfig]], a 0x30-byte struct with 1-byte alignment, a s32, a [[#ConnectOption]], no output. |
| | | |
| === ConnectPrivate === | | === ConnectPrivate === |
| + | Takes a [[#SecurityConfig]], [[#SecurityParameter]], a 0x30-byte struct with 1-byte alignment, a s32, a [[#ConnectOption]], a 0x20-byte struct with 8-byte alignment, no output. |
| | | |
| === Disconnect === | | === Disconnect === |
Line 254: |
Line 264: |
| | | |
| === SetOperationMode === | | === SetOperationMode === |
| + | Takes an input [[#OperationMode]], no output. |
| | | |
| === InitializeSystem2 === | | === InitializeSystem2 === |
Line 599: |
Line 610: |
| = AddressEntry = | | = AddressEntry = |
| This is "nn::ldn::AddressEntry". This is a 0x24-byte struct. | | This is "nn::ldn::AddressEntry". This is a 0x24-byte struct. |
| + | |
| + | = AcceptPolicy = |
| + | This is "nn::ldn::AcceptPolicy". This is an u8. |
| + | |
| + | = MacAddress = |
| + | This is "nn::ldn::MacAddress". This is a 6-byte struct with 1-byte alignment. |
| + | |
| + | = NodeInfo = |
| + | This is "nn::ldn::NodeInfo". |
| + | |
| + | {| class="wikitable" border="1" |
| + | |- |
| + | ! Offset |
| + | ! Size |
| + | ! Description |
| + | |- |
| + | | 0x0 || 0x4 || |
| + | |- |
| + | | 0x4 || 0x6 || [[#MacAddress]] |
| + | |} |
| + | |
| + | = ConnectOption = |
| + | This is "nn::ldn::ConnectOption". This is an u32 bitmask. |
| + | |
| + | There's two versions of the sdknso funcs for [[#Connect]]/[[#ConnectPrivate]]: the version where the ConnectOption isn't user-specified uses a default value of 0x1 for it, with the same ShowError code without the bit0 check. |
| + | |
| + | When bit0 here is set after using the above cmds, the sdknso funcs will use [[Error_Applet|ShowError]] with the returned Result if: (rc & 0x3FE1FF) == 0xE0CB. |
| + | |
| + | = OperationMode = |
| + | This is "nn::ldn::OperationMode". This is an u32. |
| | | |
| [[Category:Services]] | | [[Category:Services]] |