Bus services

gpio

This is "nn::gpio::IManager".

Cmd	Name
0	#OpenSessionForDev
1	#OpenSession
2	#OpenSessionForTest
3	[1.0.0-6.2.0] IsWakeEventActive
4	[1.0.0-6.2.0] GetWakeEventActiveFlagSet
5	[1.0.0-6.2.0] SetWakeEventActiveFlagSetForDebug
6	SetWakePinDebugMode
7	[5.0.0+] #OpenSession2
8	[5.0.0+] IsWakeEventActive2
9	[5.0.0+] SetWakeEventActiveFlagSetForDebug2
10	[6.0.0+]

Known Devices

GpioPadName	GpioPadDescriptor	DeviceCode	Tegra (port, pin)	Usage	Direction	Used by
0x01	0xCC	0x33000002	Z, 4	Audio Codec (ALC5639) Power (CODEC_LDO_EN_TEMP)	Out	Audio services, Fatal services
0x02	0x24	0x3C000001	E, 4	SDCard Power (POW_SD_EN)	Out	Filesystem services
0x03	0x3C	0x37000002	H, 4	Bluetooth Reset (BT_RST_PH4)	Out	Bluetooth Driver services
0x04	0xDA	0xC9000402	BB, 2	Secondary Boot Device Configration (RAM_CODE3)	In
0x05	0xDB	0x3C000402	BB, 3	GcAsic Reset (GC_RST)	Out	Filesystem services
0x06	0xDC	0x33000003	BB, 4	Audio Codec (ALC5639) Alert (CODEC_ALERT)	In	Audio services
0x07	0x25	0x3C000401	E, 5	GcAsic Power (POW_GC)	Out
0x08	0x90	0x350000CA	S, 0	Debug Pad Detect (DEBUG_CONTROLLER_DET)	In	HID services
0x09	0x91	0x39000407	S, 1	Battery Charge Status (BATT_CHG_STATUS)	In
0x0A	0x96	0x39000003	S, 6	Charger IC (BQ24193) Charge Enable (BATT_CHG_ENABLE_N)	Out	PTM services
0x0B	0x97	0x3D000002	S, 7	CPU Fan Tachometer (FAN_TACH)	In
0x0C	0x26	0x3500040B	E, 6	Joy-Con(L) IsAttached (insertion, Joy-Con pin 5/console TX, pulled low on insert?) (EXTCON_DET_S)	In	HID services
0x0D	0x05	0x39000401	A, 5	Fan Enable (normal) (VDD50A_EN)	Out	PTM services
0x0E	0x78	0xCA000402	P, 0	SDEV Coax Select (SDEV_COAX_SEL_1)	In
0x0F	0x93	0x3C000403	S, 3	GcAsic Card Detect (GC_CD)	In	Filesystem services
0x10	0x7D	0xC900040B	P, 5	PROD_TYPE_0	In
0x11	0x7C	0xC900040C	P, 4	PROD_TYPE_1	In
0x12	0x7B	0xC900040D	P, 3	PROD_TYPE_2	In
0x13	0x7A	0xC900040E	P, 2	PROD_TYPE_3	In
0x14	0xBC	0x3E000002	X, 4	Temperature Sensor (TEMP_ALERT)	In
0x15	0xAE	0x33000004	V, 6	Audio Codec (ALC5639) Headphone Detect (CODEC_HP_DET_IRQ)	In	Audio services
0x16	0xBA	0x35000041	X, 2	MOTION_INT_PX2	In
0x17	0xB9	0x35000036	X, 1	TouchPanel IRQ (TP_IRQ) (unused - polled instead)	In	HID services
0x18	0xBD	0x35000001	X, 5	Power Button (BUTTON_POWER_ON_PX5)	In
0x19	0xBE	0x35000002	X, 6	Volume Up (BUTTON_VOL_UP_PX6)	In	Boot2, Audio services
0x1A	0xBF	0x35000003	X, 7	Volume Down (BUTTON_VOL_DOWN_PX7)	In	Boot2, Audio services
0x1B	0xC0	0x39000034	Y, 0	Fuel Gauge IC (MAX17050) IRQ (BATT_MGIC_IRQ)	In	PTM services
0x1C	0xC1	0x35000004	Y, 1	Recovery Mode Key (BUTTON_HOME_PY1)	In
0x1D	0xA9	0x3400003E	V, 1	Backlight Enable (LCD_BL_EN_PV1)	Out	NV services, Backlight services
0x1E	0xAA	0x34000033	V, 2	Backlight Reset (LCD_RST_PV2)	Out	NV services
0x1F	0x55	0x040000CC	K, 5	USB-PD Controller (RHOM BM92T30MWV) VCONN Power (PD_VCONN_EN)	Out	PTM services, USB services
0x20	0xAD	0x040000CA	V, 5	USB-PD Controller (RHOM BM92T30MWV) Reset (PD_RST)	Out	USB services
0x21	0xC8	0x39000002	Z, 0	Charger IC (BQ24193) IRQ (BQ24193_IRQ)	In	PTM services
0x22	0xCA	0xCA000401	Z, 2	SDEV Coax Select (SDEV_COAX_SEL_0)	In
0x23	0xCB	0x3C000003	Z, 3	SDCard Write Protect (SD_WP)	In
0x24	0x4F	0x35000035	J, 7	TouchPanel Reset (TP_RST)	Out	HID services
0x25	0x50	0x37000401	K, 0	BT_GPIO_2	In
0x26	0x51	0x37000402	K, 1	BT_GPIO_3	In
0x27	0x52	0x37000403	K, 2	BT_GPIO_4	In
0x28	0x54	0x040000CB	K, 4	USB-PD Controller (RHOM BM92T30MWV) IRQ (PD_IRQ)	In	USB services
0x29	0x56	0x3E000003	K, 6	POW_VCPU_INT	In
0x2A	0x57	0x3E000004	K, 7	MAX77621_GPU_INT	In
0x2B	0x53	0x35000402	K, 3	Joy-Con(R) Charge Detect (EXTCON_CHG_U)	Out	HID services
0x2C	0xE3	0x3500040C	CC, 3	Joy-Con(L) Charge Detect (EXTCON_CHG_S)	Out	HID services
0x2D	0x38	0x38000003	H, 0	WIFI_RF_DISABLE	Out
0x2E	0x39	0x38000002	H, 1	WIFI_RST_PH1	Out	Wlan services, PCIe services
0x2F	0x3B	0x37000003	H, 3	AP_WAKE_BT_PH3	Out	Bluetooth Driver services
0x30	0x3D	0x37000004	H, 5	BT_WAKE_AP	In
0x31	0x3F	0x37000404	H, 7	BT_GPIO_5	Out
0x32	0x40	0x34000034	I, 0	Backlight +5V (LCD_VDD_P_EN)	Out	NV services
0x33	0x41	0x34000035	I, 1	Backlight -5V (LCD_VDD_N_EN)	Out	NV services
0x34	0x3E	0x35000401	H, 6	Joy-Con(R) IsAttached (insertion, Joy-Con pin 5/console TX, pulled low on insert?) (EXTCON_DET_U)	In	HID services
0x35	0xE2	0xC9000401	CC, 2	Secondary Boot Device Configration (RAM_CODE2)	In
0x36	0xE4	0x39000402	CC, 4	Fan Enable (high power) (VDD50B_EN)	Out	PTM services
0x37	0x3A	0x38000004	H, 2	WIFI_WAKE_HOST	In
0x38	0xC9	0x3C000002	Z, 1	SDCard Card Detect (SD_CD)	In	Filesystem services
0x39	0x4D	0x39000404	J, 5	Charger IC (BQ24193) OTG Charge Select (OTG_FET_1)	Out	PTM services, USB services
0x3A	0x58	0x39000405	L, 0	Charger IC (BQ24193) OTG Charge Select (OTG_FET_2)	Out	PTM services, USB services
0x3B	0x3E	0x35000403	H, 6	Joy-Con(R) Wake Detect (EXTCON_DET_U)	In
0x3C	0x26	0x3500040D	E, 6	Joy-Con(L) Wake Detect (EXTCON_DET_S)	In
0x3D	-1	0x39000406
0x3E	0x33	0x35000404	G, 3	Joy-Con(R) CTS (checked low) (EXT_UART2_CTS)	In	HID services
0x3F	0x1C	0x3500040E	D, 4	Joy-Con(L) CTS (checked low) (EXT_UART3_CTS)	In	HID services
0x40	0xD9	0x39000408	BB, 1	5V Step-Down Regulator Power (5V_STEPDOWN_EN)	Out	(SDEV only)
0x41	0x0C	0x04000401	B, 4	USB Root Port 2 Over Current (USB_B2_OC)	In	(SDEV only)
0x42	0x0D	0x39000409	B, 5	5V Step-Down Regulator Power Good Flag (5V_STEPDOWN_PG)	In	(SDEV only)
0x43	0x21	0x04000402	E, 1	USB Power (USB_A_EN)	Out	USB services (SDEV only)
0x44	0x27	0x04000403	E, 7	USB Power Flag (USB_A_FLAG)	In	USB services (SDEV only)
0x45	0x92	0x04000404	S, 2	USB Root Port 3 Over Current (USB_B3_OC)	In	USB services (SDEV only)
0x46	0x95	0x04000405	S, 5	USB Root Port 3 Power (USB_B3_EN)	Out	USB services (SDEV only)
0x47	0x98	0x04000406	T, 0	USB Root Port 2 Power (USB_B2_EN)	Out	USB services (SDEV only)
0x48	0x10	0x34000004	C, 0	HDMI 5V (HDMI_5V_EN)	Out	[2.0.0+] NV services (SDEV only)
0x49	0x11	0x04000407	C, 1	USB Root Port 1 Power (USB_B1_EN)	Out	USB services (SDEV only)
0x4A	0x12	0x34000005	C, 2	HDMI/Power Delivery Switch (HDMI_PD_TR_EN)	Out	NV services (SDEV only)
0x4B	0x42	0x3D000003	I, 2	FAN_EN	Out	(SDEV only)
0x4C	0xE6	0x04000408	CC, 6	USB Root Port 1 Over Current (USB_B1_OC)	In	(SDEV only)
[2.0.0+] 0x4D	0xAC	0x3D000001	V, 4	PWM_FAN	Out	(SDEV only)
[2.0.0+] 0x4E	0xE1	0x34000006	CC, 1	HDMI Hot Plug Detect (HDMI_INT_DP_HPD_PCC1)	In	NV services (SDEV only)
[5.0.0+] 0x4F	0x56	0x3E000003	K, 6	MAX77812_IRQ
[6.0.0+] 0x50	0x20	0xCA000001	E, 0
[6.0.0+] 0x51	0x21	0xCA000002	E, 1
[6.0.0+] 0x52	0x22	0xCA000003	E, 2
[6.0.0+] 0x53	0x23	0xCA000004	E, 3
[6.0.0+] 0x54	0x4C	0x36000004	J, 4	NFC_IRQ
[6.0.0+] 0x55	0x57	0x36000003	K, 7	NFC_RST
[6.0.0+] 0x56	0x94	0x35000415	S, 4	MCU_IRQ
[6.0.0+] 0x57	0x98	0x35000416	T, 0	MCU_BOOT
[6.0.0+] 0x58	0x99	0x35000417	T, 1	MCU_RST
[6.0.0+] 0x59	0xBB	0x39000403	X, 3	VDD5V3_EN
[6.0.0+] 0x5A	0xE5	0x35000418	CC, 5	MCU_POR
[6.0.0+] 0x5B	0xAB	0x35000005	V, 3
[6.0.0+] 0x5C	0x4E	0x36000002	J, 6
[7.0.0+] -	0x32	0x35000406	G, 2	Joy-Con(R) RTS
[7.0.0+] -	0x1B	0x35000410	D, 3	Joy-Con(L) RTS
[7.0.0+] -	0x17	0x3500041B
[7.0.0+] -	0x18	0x3500041C
[7.0.0+] -	0x15	0x3500041D
[7.0.0+] -	0x16	0x3500041E
[8.0.0+] -	0x27	0x35000415	S, 4	MCU_IRQ (duplicate)

GpioPadDescriptor

Bits	Description
7-5	Controller index
4-3	Port index
2-0	Pin number

OpenSessionForDev

Takes a raw #GpioPadDescriptor and returns a #IPadSession session for it.

OpenSession

Same thing as #OpenSessionForDev except it takes a GpioPadName which is then converted to a #GpioPadDescriptor. Returns an #IPadSession session.

OpenSessionForTest

Same as #OpenSession but panics on failure.

OpenSession2

Same as #OpenSession but takes a DeviceCode instead of a GpioPadName.

IPadSession

This is "nn::gpio::IPadSession".

Cmd	Name
0	SetDirection
1	GetDirection
2	SetInterruptMode
3	GetInterruptMode
4	SetInterruptEnable
5	GetInterruptEnable
6	GetInterruptStatus
7	ClearInterruptStatus
8	SetValue
9	GetValue
10	BindInterrupt
11	UnbindInterrupt
12	SetDebounceEnabled
13	GetDebounceEnabled
14	SetDebounceTime
15	GetDebounceTime
16	[4.0.0+] SetValueForSleepState
17	[6.0.0+] GetValueForSleepState

i2c, i2c:pcv

This is "nn::i2c::IManager".

Cmd	Name
0	OpenSessionForDev
1	OpenSession
[1.0.0-5.1.0] 2	HasDevice
[1.0.0-5.1.0] 3	HasDeviceForDev
4	[6.0.0+] OpenSession2

Known Devices

Name	DeviceCode	Port:Addr	Is10bit	Speed	Max Retries	Retry Delay	Usage	Used by
0	0x350000C9	0:52	N	100000	0	0	DebugPadDriver	HID services
1	0x35000033	2:49	N	400000	0	0	TouchPanel	HID services
2	0x3E000001	0:4c	N	100000	0	0	Temperature Sensor (TMP451 or NCT72)	PTM services
3	0x3E000001	0:4c	N	100000	0	0	Temperature Sensor (TMP451 or NCT72) (duplicate)
4	0x33000001	0:1c	N	100000	0	0	Audio Codec (ALC5639)	Audio services, Fatal services
5	0x3B000001	4:68	N	400000	3	5000000	PMIC RTC (max77620_rtc0), max77620_irq0	PCV services
6	0x3A000001	4:3c	N	400000	3	5000000	PMIC (MAX77620), max77620_irq0	PCV services
7	0x3A000003	4:1b	N	400000	3	5000000	Sub-PMIC for CPU (max77621_cpu)	PCV services
8	0x3A000004	4:1c	N	400000	3	5000000	Sub-PMIC for GPU (max77621_gpu)	PCV services
9	0x39000001	0:6b	N	100000	3	5000000	Charger IC (BQ24193)	PTM services
10	0x39000033	0:36	N	100000	3	5000000	Fuel Gauge IC (MAX17050)	PCV services, PTM services
11	0x040000C9	0:18	N	100000	3	5000000	USB-PD controller (RHOM BM92T30MWV)	USB services
12	0x3F000401	1:40	N	400000	3	5000000	Power Monitor (ina226_V_VDD15V0-HB)	Factory testing
13	0x3F000001	1:41	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-CPU-DS)	Factory testing
14	0x3F000002	1:44	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-GPU-DS)	Factory testing
15	0x3F000003	1:45	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-DDR-DS)	Factory testing
16	0x3F000402	1:46	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-AP)	Factory testing
17	0x3F000403	1:47	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-BL-DS)	Factory testing
18	0x35000047	1:29	N	400000	3	5000000	Ambient Light Sensor (BH1730)	Backlight services
19	0x3F000404	1:48	N	400000	3	5000000	Power Monitor (ina226_CORE)	Factory testing
20	0x3F000405	1:49	N	400000	3	5000000	Power Monitor (ina226_Soc-1V8)	Factory testing
21	0x3F000406	1:4a	N	400000	3	5000000	Power Monitor (ina226_LPDDR4-1V8)	Factory testing
22	0x3F000407	1:4b	N	400000	3	5000000	Power Monitor (ina226_REG1V32)	Factory testing
23	0x3F000408	1:4d	N	400000	3	5000000	Power Monitor (ina226_VDD3V3-SYS)	Factory testing
[2.0.0+] 24	0x34000001	3:50	N	100000	0	0	HDMI DDC	NV services
[2.0.0+] 25	0x34000002	3:54	N	100000	0	0	HDMI SCDC	NV services
[2.0.0+] 26	0x34000003	3:3a	N	100000	0	0	HDMI HDCP	NV services
[4.0.0+] 27	0x3A000005	4:a4	N	400000	0	0	Fan (Fan53528)
[4.0.0+] 28	0x3A000002	4:31	N	400000	0	0	PMIC (Max77812)
[4.0.0+] 29	0x3A000002	4:33	N	400000	0	0	PMIC (Max77812)
[4.0.0+] 30	0x3F000409	1:4e	N	400000	3	5000000	Power Monitor (ina226_V_VDD-DDR-0V6)
[8.0.0+] 31	0x36000001	1:08	N	400000	3	5000000

OpenSessionForDev

Takes an u32 port, an u16 addr, an AddressingMode (1 for 10-bit, 0 otherwise) and a SpeedMode (400000 or 100000). Returns a #II2cSession session.

OpenSession

Takes an I2cDevice and returns a #II2cSession session for it.

HasDevice

Takes an I2cDevice and returns true if the device exists or false otherwise.

HasDeviceForDev

Takes an u32 port, an u16 addr, an AddressingMode (1 for 10-bit, 0 otherwise) and a SpeedMode (400000 or 100000). Returns true if the device exists or false otherwise.

OpenSession2

Same as OpenSession but takes a DeviceCode instead of a I2cDevice.

II2cSession

This is "nn::i2c::ISession".

Cmd	Name
[1.0.0-5.1.0] 0	Send
[1.0.0-5.1.0] 1	Receive
[1.0.0-5.1.0] 2	ExecuteCommandList
10	#SendAuto
11	ReceiveAuto
12	#ExecuteCommandListAuto
13	[6.0.0+]

SendAuto

Takes bytes to write in either a static buffer or a receive buffer, returns an error code for success

ExecuteCommandListAuto

Takes a command list from either a static buffer or a receive buffer, returns data in either a static (or recieve?) buffer.

Commands

• 0x40 [u8 len] <bytes> - Write bytes to device
• 0xC1 [u8 len] - Receive bytes from device

uart

This is "nn::uart::IManager".

Cmd	Name
0	#DoesUartExist
1	DoesUartExistForTest
2	#IsUartBaudrateValid
3	IsUartBaudrateValidForTest
4	#IsSomethingUartValid
5	IsSomethingUartValidForTest
6	#GetSession
7	IsSomethingUartValid2
8	IsSomethingUartValid2ForTest
9	[7.0.0+] IsSomethingUartValid3
10	[7.0.0+] IsSomethingUartValid3ForTest

DoesUartExist

Takes a u32 #UartPort and returns boolean success value

IsUartBaudrateValid

Takes a u32 #UartPort and a u32 baudrate and returns boolean success value

IsSomethingUartValid

Takes a u32 #UartPort and returns boolean success value

GetSession

Takes a u32 #UartPort and returns an #IPortSession

UartPort

Name	Port	Usage
1	UART-D	Bluetooth
2	UART-B	Joy-Con(R)
3	UART-C	Joy-Con(L)

IPortSession

This is "nn::uart::IPortSession".

Cmd	Name
0	OpenSession
1	OpenSessionForTest
2
3
4
5
6
7

[7.0.0+] OpenSession/OpenSessionForTest now takes an additional 0x8-bytes of input.

Port Mapping

OpenSession translates user IDs to to the #UartPort index.

OpenSessionForTest takes the port index verbatim.

pwm

This is "nn::pwm::IManager".

Cmd	Name
0	OpenSessionForDev
1	OpenSession
2	[6.0.0+]

Known Channels

Name	Interface	Usage	Used by
1	PWM Channel 1	Fan	PTM services
2	PWM Channel 0	Backlight	Backlight services, NV services
3	PMC Blinker

IChannelSession

This is "nn::pwm::IChannelSession".

Cmd	Name
0	SetPeriod
1	GetPeriod
2	SetDuty
3	GetDuty
4	SetEnabled
5	GetEnabled
6	[6.0.0+]
7	[6.0.0+]

pinmux

This is "nn::pinmux::IManager".

Cmd	Name
0	OpenSession

ISession

This is "nn::pinmux::ISession".

Cmd	Name
0	SetPinAssignment
1	GetPinAssignment
2	SetPinAssignmentForHardwareTest

sasbus

This is "nn::sasbus::IManager".

Cmd	Name
0	OpenSession

ISession

This is "nn::sasbus::ISession".

Cmd	Name
0
1
2
3