Bus services

gpio

This is "nn::gpio::IManager".

Cmd	Name
0	#OpenSessionForDev
1	#OpenSession
2	#OpenSessionForTest
3	[1.0.0-6.2.0] IsWakeEventActive
4	[1.0.0-6.2.0] GetWakeEventActiveFlagSet
5	[1.0.0-6.2.0] SetWakeEventActiveFlagSetForDebug
6	SetWakePinDebugMode
7	[5.0.0+] #OpenSession2
8	[5.0.0+] IsWakeEventActive2
9	[5.0.0+] SetWakeEventActiveFlagSetForDebug2
10	[6.0.0+]

Known Devices

GpioPadName	GpioPadDescriptor	DeviceCode	Tegra (port, pin)	Usage	Direction	Used by (services)	Used by (hardware)
0x01	0xCC	0x33000002	Z, 4	Audio Codec (ALC5639) Power (CODEC_LDO_EN_TEMP)	Out	Audio services, Fatal services	Icosa, Hoag, Iowa
0x02	0x24	0x3C000001	E, 4	SDCard Power (POW_SD_EN)	Out	PCV services	Icosa, Copper, Hoag, Iowa, Calcio
0x03	0x3C	0x37000002	H, 4	Bluetooth Reset (BT_RST_PH4)	Out	Bluetooth Driver services	Icosa, Copper, Hoag, Iowa, Calcio
0x04	0xDA	0xC9000402	BB, 2	Secondary Boot Device Configration (RAM_CODE3)	In		Icosa, Iowa
0x05	0xDB	0x3C000402	BB, 3	Gamecard Reset (GC_RST)	Out	Filesystem services	Icosa, Copper, Hoag, Iowa
0x06	0xDC	0x33000003	BB, 4	Audio Codec (ALC5639) Alert (CODEC_ALERT)	In	Audio services	Icosa, Hoag, Iowa
0x07	0x25	0x3C000401	E, 5	Gamecard Power (POW_GC)	Out		Icosa, Copper
0x08	0x90	0x350000CA	S, 0	Debug Pad Detect (DEBUG_CONTROLLER_DET)	In	HID services	Icosa, Iowa
0x09	0x91	0x39000407	S, 1	Battery Charge Status (BATT_CHG_STATUS)	In		Icosa, Hoag, Iowa
0x0A	0x96	0x39000003	S, 6	Charger IC (BQ24193) Charge Enable (BATT_CHG_ENABLE_N)	Out	PTM services	Icosa, Hoag, Iowa
0x0B	0x97	0x3D000002	S, 7	Fan Tachometer (FAN_TACH)	In		Icosa, Hoag, Iowa, Calcio
0x0C	0x26	0x3500040B	E, 6	Joy-Con(L) IsAttached (insertion, Joy-Con pin 5/console TX, pulled low on insert) (EXTCON_DET_S)	In	HID services	Icosa, Iowa
0x0D	0x05	0x39000401	A, 5	Fan and Joy-Con Rails Power (Battery - BQ24193 5V) (VDD50A_EN)	Out	PTM services	Icosa, Hoag, Iowa
0x0E	0x78	0xCA000402	P, 0	SDEV Coax Select (SDEV_COAX_SEL_1)	In		Icosa, Iowa
0x0F	0x93	0x3C000403	S, 3	Gamecard Card Detect (GC_CD)	In	Filesystem services	Icosa, Copper, Hoag, Iowa
0x10	0x7D	0xC900040B	P, 5	PROD_TYPE_0	In		Icosa, Copper, Iowa
0x11	0x7C	0xC900040C	P, 4	PROD_TYPE_1	In		Icosa, Copper, Iowa
0x12	0x7B	0xC900040D	P, 3	PROD_TYPE_2	In		Icosa, Copper, Iowa
0x13	0x7A	0xC900040E	P, 2	PROD_TYPE_3	In		Icosa, Copper, Iowa
0x14	0xBC	0x3E000002	X, 4	Temperature Sensor (TEMP_ALERT)	In		Icosa, Copper, Hoag, Iowa, Calcio
0x15	0xAE	0x33000004	V, 6	Audio Codec (ALC5639) Headphone Detect (CODEC_HP_DET_IRQ)	In	Audio services	Icosa, Hoag, Iowa
0x16	0xBA	0x35000041	X, 2	MOTION_INT_PX2	In		Icosa, Hoag, Iowa
0x17	0xB9	0x35000036	X, 1	TouchPanel IRQ (TP_IRQ)	In	HID services	Icosa, Hoag, Iowa
0x18	0xBD	0x35000001	X, 5	Power Button (BUTTON_POWER_ON_PX5)	In		Icosa, Copper, Hoag, Iowa, Calcio
0x19	0xBE	0x35000002	X, 6	Volume Up (BUTTON_VOL_UP_PX6)	In	Boot2, Audio services	Icosa, Copper, Hoag, Iowa, Calcio
0x1A	0xBF	0x35000003	X, 7	Volume Down (BUTTON_VOL_DOWN_PX7)	In	Boot2, Audio services	Icosa, Copper, Hoag, Iowa, Calcio
0x1B	0xC0	0x39000034	Y, 0	Fuel Gauge IC (MAX17050) IRQ (BATT_MGIC_IRQ)	In	PTM services	Icosa, Hoag, Iowa
0x1C	0xC1	0x35000004	Y, 1	Recovery Mode Key (BUTTON_HOME_PY1)	In		Icosa, Copper, Hoag, Iowa, Calcio
0x1D	0xA9	0x3400003E	V, 1	Backlight Enable (LCD_BL_EN_PV1)	Out	NV services, Backlight services	Icosa, Hoag, Iowa
0x1E	0xAA	0x34000033	V, 2	Backlight Reset (LCD_RST_PV2)	Out	NV services	Icosa, Hoag, Iowa
0x1F	0x55	0x040000CC	K, 5	USB-PD Controller (RHOM BM92T30MWV) VCONN Power (PD_VCONN_EN)	Out	PTM services, USB services	Icosa, Hoag, Iowa
0x20	0xAD	0x040000CA	V, 5	USB-PD Controller (RHOM BM92T30MWV) Reset (PD_RST)	Out	USB services	Icosa, Copper, Hoag, Iowa, Calcio
0x21	0xC8	0x39000002	Z, 0	Charger IC (BQ24193) IRQ (BQ24193_IRQ)	In	PTM services	Icosa, Hoag, Iowa
0x22	0xCA	0xCA000401	Z, 2	SDEV Coax Select (SDEV_COAX_SEL_0)	In		Icosa, Iowa
0x23	0xCB	0x3C000003	Z, 3	SDCard Write Protect (SD_WP)	In		Icosa, Copper, Hoag, Iowa, Calcio
0x24	0x4F	0x35000035	J, 7	TouchPanel Reset (TP_RST)	Out	HID services	Icosa, Hoag, Iowa
0x25	0x50	0x37000401	K, 0	BT_GPIO_2	In		Icosa, Copper, Hoag, Iowa, Calcio
0x26	0x51	0x37000402	K, 1	BT_GPIO_3	In		Icosa, Copper, Hoag, Iowa, Calcio
0x27	0x52	0x37000403	K, 2	BT_GPIO_4	In		Icosa, Copper, Hoag, Iowa, Calcio
0x28	0x54	0x040000CB	K, 4	USB-PD Controller (RHOM BM92T30MWV) IRQ (PD_IRQ)	In	USB services	Icosa, Copper, Hoag, Iowa, Calcio
0x29	0x56	0x3E000003	K, 6	POW_VCPU_INT	In		Icosa, Copper
0x2A	0x57	0x3E000004	K, 7	MAX77621_GPU_INT	In		Icosa, Copper
0x2B	0x53	0x35000402	K, 3	Joy-Con(R) Charge (EXTCON_CHG_U)	Out	HID services	Icosa, Iowa
0x2C	0xE3	0x3500040C	CC, 3	Joy-Con(L) Charge (EXTCON_CHG_S)	Out	HID services	Icosa, Iowa
0x2D	0x38	0x38000003	H, 0	WIFI_RF_DISABLE	Out		Icosa, Copper, Hoag, Iowa, Calcio
0x2E	0x39	0x38000002	H, 1	WiFi Reset (WIFI_RST_PH1)	Out	WLAN services, PCIe services	Icosa, Copper, Hoag, Iowa, Calcio
0x2F	0x3B	0x37000003	H, 3	AP_WAKE_BT_PH3	Out	Bluetooth Driver services	Icosa, Copper, Hoag, Iowa, Calcio
0x30	0x3D	0x37000004	H, 5	BT_WAKE_AP	In		Icosa, Copper, Hoag, Iowa, Calcio
0x31	0x3F	0x37000404	H, 7	BT_GPIO_5	Out		Icosa, Copper, Hoag, Iowa, Calcio
0x32	0x40	0x34000034	I, 0	Backlight +5V (LCD_VDD_P_EN)	Out	NV services	Icosa, Hoag, Iowa
0x33	0x41	0x34000035	I, 1	Backlight -5V (LCD_VDD_N_EN)	Out	NV services	Icosa, Hoag, Iowa
0x34	0x3E	0x35000401	H, 6	Joy-Con(R) IsAttached (insertion, Joy-Con pin 5/console TX, pulled low on insert) (EXTCON_DET_U)	In	HID services	Icosa, Iowa
0x35	0xE2	0xC9000401	CC, 2	Secondary Boot Device Configration (RAM_CODE2)	In		Icosa, Iowa
0x36	0xE4	0x39000402	CC, 4	Fan and Joy-Con Rails Power (USB 5V) (VDD50B_EN)	Out	PTM services	Icosa, Iowa
0x37	0x3A	0x38000004	H, 2	WIFI_WAKE_HOST	In		Icosa, Copper, Hoag, Iowa, Calcio
0x38	0xC9	0x3C000002	Z, 1	SDCard Card Detect (SD_CD)	In	Filesystem services	Icosa, Copper, Hoag, Iowa, Calcio
0x39	0x4D	0x39000404	J, 5	Charger IC (BQ24193) OTG Charge Select (OTG_FET_1)	Out	PTM services, USB services	Icosa, Iowa
0x3A	0x58	0x39000405	L, 0	Charger IC (BQ24193) OTG Charge Select (OTG_FET_2)	Out	PTM services, USB services	Icosa, Iowa
0x3B	0x3E	0x35000403	H, 6	Joy-Con(R) Wake Detect (EXTCON_DET_U)	In		Icosa, Hoag, Iowa
0x3C	0x26	0x3500040D	E, 6	Joy-Con(L) Wake Detect (EXTCON_DET_S)	In		Icosa, Hoag, Iowa
0x3D	-1	0x39000406
0x3E	0x33	0x35000404	G, 3	Joy-Con(R) CTS (checked low) (EXT_UART2_CTS)	In	HID services
0x3F	0x1C	0x3500040E	D, 4	Joy-Con(L) CTS (checked low) (EXT_UART3_CTS)	In	HID services
0x40	0xD9	0x39000408	BB, 1	5V Step-Down Regulator Power (5V_STEPDOWN_EN)	Out		Copper
0x41	0x0C	0x04000401	B, 4	USB Root Port 2 Over Current (USB_B2_OC)	In	USB services	Copper
0x42	0x0D	0x39000409	B, 5	5V Step-Down Regulator Power Good Flag (5V_STEPDOWN_PG)	In		Copper
0x43	0x21	0x04000402	E, 1	USB Power (USB_A_EN)	Out	USB services	Copper
0x44	0x27	0x04000403	E, 7	USB Power Flag (USB_A_FLAG)	In	USB services	Copper
0x45	0x92	0x04000404	S, 2	USB Root Port 3 Over Current (USB_B3_OC)	In	USB services	Copper
0x46	0x95	0x04000405	S, 5	USB Root Port 3 Power (USB_B3_EN)	Out	USB services	Copper
0x47	0x98	0x04000406	T, 0	USB Root Port 2 Power (USB_B2_EN)	Out	USB services	Copper
0x48	0x10	0x34000004	C, 0	HDMI 5V (HDMI_5V_EN)	Out	NV services	Copper, Calcio
0x49	0x11	0x04000407	C, 1	USB Root Port 1 Power (USB_B1_EN)	Out	USB services	Copper, Calcio
0x4A	0x12	0x34000005	C, 2	HDMI/Power Delivery Switch (HDMI_PD_TR_EN)	Out	NV services	Copper, Calcio
0x4B	0x42	0x3D000003	I, 2	Fan Enable (FAN_EN)	Out	PTM services	Copper
0x4C	0xE6	0x04000408	CC, 6	USB Root Port 1 Over Current (USB_B1_OC)	In	USB services	Copper, Calcio
[2.0.0+] 0x4D	0xAC	0x3D000001	V, 4	Pulse-Width Modulation Fan Control (PWM_FAN)	Out	PTM services	Copper
[2.0.0+] 0x4E	0xE1	0x34000006	CC, 1	HDMI Hot Plug Detect (HDMI_INT_DP_HPD_PCC1)	In	NV services	Copper, Calcio
[5.0.0+] 0x4F	0x56	0x3E000003	K, 6	MAX77812_IRQ	In		Hoag, Iowa, Calcio
[6.0.0+] 0x50	0x20	0xCA000001	E, 0		Out		Hoag, Calcio
[6.0.0+] 0x51	0x21	0xCA000002	E, 1		Out		Hoag, Calcio
[6.0.0+] 0x52	0x22	0xCA000003	E, 2		Out		Hoag, Calcio
[6.0.0+] 0x53	0x23	0xCA000004	E, 3		Out		Hoag, Calcio
[6.0.0+] 0x54	0x4C	0x36000004	J, 4	NFC_IRQ	In	NFC services	Hoag
[6.0.0+] 0x55	0x57	0x36000003	K, 7	NFC_RST	Out	NFC services	Hoag
[6.0.0+] 0x56	0x27 ([6.0.0-8.0.0] 0x94)	0x35000415	S, 4	MCU_IRQ	In		Hoag
[6.0.0+] 0x57	0x98	0x35000416	T, 0	MCU_BOOT	Out	HID services	Hoag
[6.0.0+] 0x58	0x99	0x35000417	T, 1	MCU_RST	Out	HID services	Hoag
[6.0.0+] 0x59	0xBB	0x39000403	X, 3	Fan Power (5V3) (VDD5V3_EN)	Out	PTM services	Hoag, Iowa
[6.0.0+] 0x5A	0xE5	0x35000418	CC, 5	MCU_POR	Out	HID services	Hoag
[6.0.0+] 0x5B	0xAB	0x35000005	V, 3	SioH Input (LCD_GPIO1_PV3)	In	HID services	Hoag
[6.0.0+] 0x5C	0x4E	0x36000002	J, 6	NFC_EN	Out	NFC services	Hoag
[7.0.0+] 0x5D	0x32	0x35000406	G, 2	Joy-Con(R) RTS (EXT_UART2_RTS)	In
[7.0.0+] 0x5E	0x1B	0x35000410	D, 3	Joy-Con(L) RTS (EXT_UART3_RTS)	In
[7.0.0+] 0x5F	0x17	0x3500041B	C, 7		In		Hoag
[7.0.0+] 0x60	0x18	0x3500041C	D, 0		In		Hoag
[7.0.0+] 0x61	0x15	0x3500041D	C, 5		In		Hoag
[7.0.0+] 0x62	0x16	0x3500041E	C, 6		In		Hoag

GpioPadDescriptor

Bits	Description
7-5	Controller index
4-3	Port index
2-0	Pin number

OpenSessionForDev

Takes a raw #GpioPadDescriptor and returns an #IPadSession session for it.

OpenSession

Same thing as #OpenSessionForDev except it takes a GpioPadName which is then converted to a #GpioPadDescriptor. Returns an #IPadSession session.

OpenSessionForTest

Same as #OpenSession but panics on failure.

OpenSession2

Same as #OpenSession but takes a DeviceCode instead of a GpioPadName and an u32 DeviceUnk.

IPadSession

This is "nn::gpio::IPadSession".

Cmd	Name
0	SetDirection
1	GetDirection
2	SetInterruptMode
3	GetInterruptMode
4	SetInterruptEnable
5	GetInterruptEnable
6	GetInterruptStatus
7	ClearInterruptStatus
8	SetValue
9	GetValue
10	BindInterrupt
11	UnbindInterrupt
12	SetDebounceEnabled
13	GetDebounceEnabled
14	SetDebounceTime
15	GetDebounceTime
16	[4.0.0+] SetValueForSleepState
17	[6.0.0+] GetValueForSleepState

i2c, i2c:pcv

This is "nn::i2c::IManager".

Cmd	Name
0	OpenSessionForDev
1	OpenSession
[1.0.0-5.1.0] 2	HasDevice
[1.0.0-5.1.0] 3	HasDeviceForDev
4	[6.0.0+] OpenSession2

Known Devices

Name	DeviceCode	Port:Addr	Is10bit	Speed	Max Retries	Retry Delay	Usage	Used by (services)	Used by (hardware)
0	0x350000C9	0:52	N	100000	0	0	DebugPadDriver	HID services	Icosa, Copper, Iowa
1	0x35000033	2:49	N	400000	0	0	TouchPanel	HID services	Icosa, Copper, Hoag, Iowa
2	0x3E000001	0:4c	N	100000	0	0	Temperature Sensor (TMP451 or NCT72)	PTM services	Icosa, Copper, Hoag, Iowa, Calcio
3	0x3E000001	0:4c	N	100000	0	0	Temperature Sensor (TMP451 or NCT72) (duplicate)	PTM services	Icosa, Copper, Hoag, Iowa, Calcio
4	0x33000001	0:1c	N	100000	0	0	Audio Codec (ALC5639)	Audio services, Fatal services	Icosa, Copper, Hoag, Iowa
5	0x3B000001	4:68	N	400000	3	5000000	PMIC RTC (max77620_rtc0), max77620_irq0	PCV services	Icosa, Copper
6	0x3A000001	4:3c	N	400000	3	5000000	PMIC (MAX77620), max77620_irq0	PCV services	Icosa, Copper
7	0x3A000003	4:1b	N	400000	3	5000000	Sub-PMIC for CPU (max77621_cpu)	PCV services	Icosa, Copper
8	0x3A000004	4:1c	N	400000	3	5000000	Sub-PMIC for GPU (max77621_gpu)	PCV services	Icosa, Copper
9	0x39000001	0:6b	N	100000	3	5000000	Charger IC (BQ24193)	PTM services	Icosa, Copper, Hoag, Iowa
10	0x39000033	0:36	N	100000	3	5000000	Fuel Gauge IC (MAX17050)	PTM services, PCV services	Icosa, Copper, Hoag, Iowa
11	0x040000C9	0:18	N	100000	3	5000000	USB-PD controller (RHOM BM92T30MWV)	USB services	Icosa, Copper, Hoag, Iowa, Calcio
12	0x3F000401	1:40	N	400000	3	5000000	Power Monitor (ina226_V_VDD15V0-HB)		Factory
13	0x3F000001	1:41	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-CPU-DS or SdevMariko_ina226_VDD_CPU_AP)		Factory
14	0x3F000002	1:44	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-GPU-DS or SdevMariko_ina226_VDD_GPU_AP)		Factory
15	0x3F000003	1:45	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-DDR-DS or SdevMariko_ina226_V_VDD-DDR_1V1-PMIC)		Factory
16	0x3F000402	1:46	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-AP)		Factory
17	0x3F000403	1:47	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-BL-DS)		Factory
18	0x35000047	1:29	N	400000	3	5000000	Ambient Light Sensor (BH1730)	Backlight services	Icosa, Copper, Hoag, Iowa
19	0x3F000404	1:48	N	400000	3	5000000	Power Monitor (ina226_V_SYS-CORE or SdevMariko_ina226_V_VDD-CORE-AP)		Factory
20	0x3F000405	1:49	N	400000	3	5000000	Power Monitor (ina226_V_SOC-1V8 or SdevMariko_ina226_V_VDD_SOC-1V8)		Factory
21	0x3F000406	1:4a	N	400000	3	5000000	Power Monitor (ina226_V_LPDDR-1V8 or SdevMariko_ina226_V_VDD_1V8)		Factory
22	0x3F000407	1:4b	N	400000	3	5000000	Power Monitor (ina226_V_REG-1V32)		Factory
23	0x3F000408	1:4d	N	400000	3	5000000	Power Monitor (ina226_V_VDD-3V3-SYS)		Factory
[2.0.0+] 24	0x34000001	3:50	N	100000	0	0	HDMI DDC	NV services	Copper, Calcio
[2.0.0+] 25	0x34000002	3:54	N	100000	0	0	HDMI SCDC	NV services	Copper, Calcio
[2.0.0+] 26	0x34000003	3:3a	N	100000	0	0	HDMI HDCP	NV services	Copper, Calcio
[4.0.0+] 27	0x3A000005	4:52 ([4.0.0-8.0.0] 4:a4)	N	400000	0	0	Buck Regulator (FAN53528)		Hoag, Iowa, Calcio
[4.0.0+] 28	0x3A000002	4:33 ([4.0.0-8.0.0] 4:31)	N	400000	0	0	PMIC (MAX77812)	PCV services	Hoag, Iowa, Calcio
[4.0.0+] 29	0x3A000002	4:33 ([4.0.0-8.0.0] 4:31)	N	400000	0	0	PMIC (MAX77812)	PCV services	Hoag, Iowa, Calcio
[4.0.0+] 30	0x3F000409	1:4e	N	400000	3	5000000	Power Monitor (SdevMariko_ina226_V_VDD_DDR_0V6)		Factory
[8.0.0+] 31	0x36000001	1:08	N	400000	3	5000000	NFC IC		Hoag

OpenSessionForDev

Takes an u32 port, an u16 addr, an AddressingMode (1 for 10-bit, 0 otherwise) and a SpeedMode (400000 or 100000). Returns an #II2cSession session.

OpenSession

Takes an I2cDevice and returns an #II2cSession session for it.

HasDevice

Takes an I2cDevice and returns true if the device exists or false otherwise.

HasDeviceForDev

Takes an u32 port, an u16 addr, an AddressingMode (1 for 10-bit, 0 otherwise) and a SpeedMode (400000 or 100000). Returns true if the device exists or false otherwise.

OpenSession2

Same as OpenSession but takes a DeviceCode instead of a I2cDevice.

II2cSession

This is "nn::i2c::ISession".

Cmd	Name
[1.0.0-5.1.0] 0	Send
[1.0.0-5.1.0] 1	Receive
[1.0.0-5.1.0] 2	ExecuteCommandList
10	#SendAuto
11	ReceiveAuto
12	#ExecuteCommandListAuto
13	[6.0.0+]

SendAuto

Takes bytes to write in either a static buffer or a receive buffer, returns an error code for success

ExecuteCommandListAuto

Takes a command list from either a static buffer or a receive buffer, returns data in either a static (or recieve?) buffer.

Commands

• 0x40 [u8 len] <bytes> - Write bytes to device
• 0xC1 [u8 len] - Receive bytes from device

uart

This is "nn::uart::IManager".

Cmd	Name
0	#HasPort
1	#HasPortForDev
2	#IsSupportedBaudRate
3	#IsSupportedBaudRateForDev
4	#IsSupportedFlowControlMode
5	#IsSupportedFlowControlModeForDev
6	#CreatePortSession
7	#IsSupportedPortEvent
8	#IsSupportedPortEventForDev
9	[7.0.0+] #IsSupportedDevice
10	[7.0.0+] #IsSupportedDeviceForDev

HasPort

Takes an u32 #UartPort. Returns a boolean success value.

HasPortForDev

Takes an u32 #UartPortForDev. Returns a boolean success value.

IsSupportedBaudRate

Takes an u32 #UartPort and an u32 BaudRate. Returns a boolean success value.

Supported baud rates are 57600, 115200, 1000000 and 3000000.

IsSupportedBaudRateForDev

Takes an u32 #UartPortForDev and an u32 BaudRate. Returns a boolean success value.

Supported baud rates are 57600, 115200, 1000000 and 3000000.

IsSupportedFlowControlMode

Takes an u32 #UartPort and an u32 FlowControlMode. Returns a boolean success value.

Supported modes are 0 (RTS) and 1 (CTS).

IsSupportedFlowControlModeForDev

Takes an u32 #UartPortForDev and an u32 FlowControlMode. Returns a boolean success value.

Supported modes are 0 (RTS) and 1 (CTS).

CreatePortSession

No input. Returns an #IPortSession.

IsSupportedPortEvent

Takes an u32 #UartPort and an u32 PortEvent. Returns a boolean success value.

Supported events are 0 (data), 1 (break), 2 (unknown) and 3 (unknown).

IsSupportedPortEventForDev

Takes an u32 #UartPortForDev and an u32 PortEvent. Returns a boolean success value.

Supported events are 0 (data), 1 (break), 2 (unknown) and 3 (unknown).

IsSupportedDevice

Takes an u32 #UartPort and an u32 Device. Returns a boolean success value.

Supported devices are 0 (Bluetooth) for UART-D, 0 (Joy-Con(R)) for UART-B, 0 (Joy-Con(L)) and 1 (MCU) for UART-C.

IsSupportedDeviceForDev

Takes an u32 #UartPortForDev and an u32 Device. Returns a boolean success value.

Supported devices are 0 (Bluetooth) for UART-D, 0 (Joy-Con(R)) for UART-B, 0 (Joy-Con(L)) and 1 (MCU) for UART-C.

UartPort

Name	DeviceCode (internal)	DeviceCode (mapped)	Port	Usage
0	0x03000001		UART-A	Invalid
1	0x03000004	0x37000001	UART-D	Bluetooth
2	0x03000002	0x35000405	UART-B	Joy-Con(R)
3	0x03000003	0x3500040F	UART-C	Joy-Con(L)
4	0x03000003	0x35000419	UART-C	MCU

UartPortForDev

Name	DeviceCode (internal)	DeviceCode (mapped)	Port	Usage
0	0x03000001		UART-A	Invalid
1	0x03000002	0x35000405	UART-B	Joy-Con(R)
2	0x03000003	0x3500040F	UART-C	Joy-Con(L)
3	0x03000004	0x37000001	UART-D	Bluetooth

IPortSession

This is "nn::uart::IPortSession".

Cmd	Name
0	#OpenPort
1	#OpenPortForDev
2	GetWritableLength
3	Send
4	GetReadableLength
5	Receive
6	BindPortEvent
7	UnbindPortEvent

OpenPort

Takes an u32 #UartPort, 3 u32s, 2 copy handles and 4 u8s (each padded to u32). Returns a boolean success value.

[7.0.0+] Now takes an additional u64.

OpenPortForDev

Takes an u32 #UartPortForDev, 3 u32s, 2 copy handles and 4 u8s (each padded to u32). Returns a boolean success value.

[7.0.0+] Now takes an additional u64.

pwm

This is "nn::pwm::IManager".

Cmd	Name
0	OpenSessionForDev
1	OpenSession
2	[6.0.0+] OpenSession2

Known Channels

Name	DeviceCode	Interface	Usage	Used by
1	0x3D000001	PWM Channel 1	Fan	PTM services
2	0x3400003D	PWM Channel 0	Backlight	Backlight services, NV services
3	0x35000065	PMC LED Soft Blink	Led	Bus services

IChannelSession

This is "nn::pwm::IChannelSession".

Cmd	Name
0	SetPeriod
1	GetPeriod
2	SetDuty
3	GetDuty
4	SetEnabled
5	GetEnabled
6	[6.0.0+]
7	[6.0.0+]

pinmux

This is "nn::pinmux::IManager".

Cmd	Name
0	OpenSession

OpenSession

Takes a GpioPadName and returns an ISession.

ISession

This is "nn::pinmux::ISession".

Cmd	Name
0	#SetPinAssignment
1	#GetPinAssignment
2	#SetPinAssignmentForHardwareTest

SetPinAssignment

Takes an u32 PinAssignment. No output.

GetPinAssignment

No input. Returns an u32 PinAssignment.

SetPinAssignmentForHardwareTest

Same as #SetPinAssignment.

sasbus

This is "nn::sasbus::IManager".

This was added with [3.0.0+].

Cmd	Name
0	OpenSession

OpenSession

Takes an u32 that must be 0 and returns an ISession.

This opens a session for communicating over SPI4. While code exists to support both SPI1 and SPI4 communication, SPI4 is currently hardcoded as the only available interface.

ISession

This is "nn::sasbus::ISession".

Cmd	Name
0	#Write
1	#Read
2	#StartPeriodicReceiveMode
3	#StopPeriodicReceiveMode

Write

Takes a type-0x21 input buffer and an u8 SpiCommand. No output.

Read

Takes a type-0x22 output buffer and an u8 SpiCommand. No output.

StartPeriodicReceiveMode

Takes an u8 SpiCommand (padded to u32), an u32, two u64s and a copy handle. No output.

StopPeriodicReceiveMode

No input/output.

led

This is "nn::led::detail::IManager".

This was added with [8.1.1+].

Cmd	Name
0	#OpenController

OpenController

Takes a DeviceCode (must be 0x35000065) and returns an #IController session for it.

IController

This is "nn::led::detail::IController".

This was added with [8.1.1+].

Cmd	Name
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21