Nintendo Switch Brew

Bus services: Difference between revisions

← Older edit
 
(206 intermediate revisions by 9 users not shown)
Line 6: Line 6:
! Cmd || Name
! Cmd || Name
|-
|-
| 0 || [[#OpenSessionForDev]]
| 0 || [5.0.0+] [[#OpenSessionForDevDeprecated|OpenSessionForDevDeprecated]] ([1.0.0-4.1.0] OpenSessionForDev)
|-
|-
| 1 || [[#OpenSession]]
| 1 || [5.0.0+] [[#OpenSessionDeprecated|OpenSessionDeprecated]] ([1.0.0-4.1.0] OpenSession)
|-
|-
| 2 || [[#OpenSessionForTest]]
| 2 || [5.0.0+] [[#OpenSessionForTestDeprecated|OpenSessionForTestDeprecated]] ([1.0.0-4.1.0] OpenSessionForTest)
|-
|-
| 3 || IsWakeEventActive  
| 3 || [5.0.0-6.2.0] [[#IsWakeEventActiveDeprecated|IsWakeEventActiveDeprecated]] ([1.0.0-4.1.0] IsWakeEventActive)
|-
|-
| 4 || GetWakeEventActiveFlagSet
| 4 || [5.0.0-6.2.0] [[#GetWakeEventActiveFlagSetDeprecated|GetWakeEventActiveFlagSetDeprecated]] ([1.0.0-4.1.0] GetWakeEventActiveFlagSet)
|-
|-
| 5 || SetWakeEventActiveFlagSetForDebug
| 5 || [5.0.0-6.2.0] [[#SetWakeEventActiveFlagSetForDebugDeprecated|SetWakeEventActiveFlagSetForDebugDeprecated]] ([1.0.0-4.1.0] SetWakeEventActiveFlagSetForDebug)
|-
|-
| 6 ||
| 6 || [[#SetWakePinDebugMode|SetWakePinDebugMode]]
|-
| 7 || [5.0.0+] [[#OpenSession|OpenSession]]
|-
| 8 || [5.0.0+] [[#IsWakeEventActive|IsWakeEventActive]]
|-
| 9 || [5.0.0+] [[#SetWakeEventActiveFlagSetForDebug|SetWakeEventActiveFlagSetForDebug]]
|-
| 10 || [6.0.0+] [[#DumpStateForDebug|DumpStateForDebug]]
|}
|}


== OpenSessionForDev ==
== OpenSessionForDevDeprecated ==
Takes a raw GpioPadDescriptor and returns a [[#IPadSession]] session for it.
Takes an input [[#GpioPadDescriptor]]. Returns an [[#IPadSession]].
 
== OpenSessionDeprecated ==
Same as [[#OpenSessionForDevDeprecated]] except it takes a [[#GpioPadName]] which is then converted to a [[#GpioPadDescriptor]]. Returns an [[#IPadSession]].
 
== OpenSessionForTestDeprecated ==
Same as [[#OpenSessionDeprecated]] but panics on failure.
 
== IsWakeEventActiveDeprecated ==
Takes an input [[#GpioPadName]]. Returns a bool '''IsActive'''.
 
== GetWakeEventActiveFlagSetDeprecated ==
No input. Returns an output u128 [[#WakeBitFlag]].
 
== SetWakeEventActiveFlagSetForDebugDeprecated ==
Takes an input [[#GpioPadName]] and an input bool '''IsEnabled'''. No output.
 
== SetWakePinDebugMode ==
Takes an input u32 '''WakePinDebugMode'''. No output.


== OpenSession ==
== OpenSession ==
Same thing as OpenSessionForDev except the descriptor is looked up in the table below.
Same as [[#OpenSessionDeprecated]] but takes a [[#GpioPadName|DeviceCode]] and an input [[#OpenMode]].
Returns an [[#IPadSession]] session.
 
== IsWakeEventActive ==
Same as [[#IsWakeEventActiveDeprecated]] but takes a [[#GpioPadName|DeviceCode]].
 
== SetWakeEventActiveFlagSetForDebug ==
Same as [[#SetWakeEventActiveFlagSetForDebugDeprecated]] but takes a [[#GpioPadName|DeviceCode]].
 
== DumpStateForDebug ==
Stubbed. Returns 0.
 
== IPadSession ==
This is "nn::gpio::IPadSession".


{| class="wikitable" border="1"
{| class="wikitable" border="1"
|-
|-
! GpioPadName || GpioPadDescriptor || Tegra (port, pin) || Usage || Direction || Used by
! Cmd || Name
|-
|-
| 1 || 0xCC || Z, 4 || || ||  
| 0 || [12.0.0+] [[#SetDirectionDeprecated|SetDirectionDeprecated]] ([1.0.0-11.0.1] SetDirection)
|-
|-
| 2 || 0x24 || E, 4 || SDCard Power || Out || [[Filesystem services]]
| 1 || [[#GetDirection|GetDirection]]
|-
|-
| 4 || 0xDA || BB, 2 || || ||
| 2 || [[#SetInterruptMode|SetInterruptMode]]
|-
|-
| 5 || 0xDB || BB, 3 || GcAsic Power? || Out || [[Filesystem services]]
| 3 || [[#GetInterruptMode|GetInterruptMode]]
|-
|-
| 6 || 0xDC || BB, 4 || || ||
| 4 || [[#SetInterruptEnable|SetInterruptEnable]]
|-
|-
| 7 || 0x25 || E, 5 || || ||
| 5 || [[#GetInterruptEnable|GetInterruptEnable]]
|-
|-
| 8 || 0x90 || S, 0 || || In || [[HID services]]
| 6 || [1.0.0-16.1.0] [[#GetInterruptStatus|GetInterruptStatus]]
|-
|-
| 9 || 0x91 || S, 1 || || ||
| 7 || [1.0.0-16.1.0] [[#ClearInterruptStatus|ClearInterruptStatus]]
|-
|-
| 0xA || 0x96 || S, 6 || Power supply monitor related. || Out || [[PTM services]]
| 8 || [[#SetValue|SetValue]]
|-
|-
| 0xB || 0x97 || S, 7 || || ||  
| 9 || [[#GetValue|GetValue]]
|-
|-
| 0xD || 6 || A, 6 || Battery event monitor related. || Out || [[PTM services]]
| 10 || [[#BindInterrupt|BindInterrupt]]
|-
|-
| 0xE || 0x78 || P, 0 || || ||  
| 11 || [[#UnbindInterrupt|UnbindInterrupt]]
|-
|-
| 0xF || 0x93 || S, 3 || GcAsic Irq? || In || [[Filesystem services]]
| 12 || [[#SetDebounceEnabled|SetDebounceEnabled]]
|-
|-
| 0x10 || 0x7D || P, 5 || || ||  
| 13 || [[#GetDebounceEnabled|GetDebounceEnabled]]
|-
|-
| 0x11 || 0x7C || P, 4 || || ||  
| 14 || [[#SetDebounceTime|SetDebounceTime]]
|-
|-
| 0x12 || 0x7B || P, 3 || || ||  
| 15 || [[#GetDebounceTime|GetDebounceTime]]
|-
|-
| 0x13 || 0x7A || P, 2 || || ||  
| 16 || [4.0.0+] [[#SetValueForSleepState|SetValueForSleepState]]
|-
|-
| 0x14 || 0xBC || X, 4 || || ||  
| 17 || [6.0.0+] [[#GetMaxDebounceTime|GetMaxDebounceTime]]
|-
|-
| 0x15 || 0xAE || V, 6 || || ||  
| 18 || [12.0.0+] [[#SetDirectionInput|SetDirectionInput]]
|-
|-
| 0x17 || 0xB9 || X, 1 || || In || [[HID services]]
| 19 || [12.0.0+] [[#SetDirectionOutput|SetDirectionOutput]]
|}
 
=== SetDirectionDeprecated ===
Takes an input u32 [[#Direction]]. No output.
 
=== GetDirection ===
No input. Returns an output u32 [[#Direction]].
 
=== SetInterruptMode ===
Takes an input u32 [[#InterruptMode]]. No output.
 
=== GetInterruptMode ===
No input. Returns an output u32 [[#InterruptMode]].
 
=== SetInterruptEnable ===
Takes an input bool '''IsEnable'''. No output.
 
=== GetInterruptEnable ===
No input. Returns an output bool '''IsEnable'''.
 
=== GetInterruptStatus ===
No input. Returns an output u32 [[#InterruptStatus]].
 
=== ClearInterruptStatus ===
No input/output.
 
=== SetValue ===
Takes an input u32 [[#GpioValue]]. No output.
 
=== GetValue ===
No input. Returns an output u32 [[#GpioValue]].
 
=== BindInterrupt ===
No input. Returns an output Event handle.
 
=== UnbindInterrupt ===
No input/output.
 
=== SetDebounceEnabled ===
Takes an input bool '''IsEnable'''. No output.
 
=== GetDebounceEnabled ===
No input. Returns an output bool '''IsEnable'''.
 
=== SetDebounceTime ===
Takes an input s32 '''MsecTime'''. No output.
 
=== GetDebounceTime ===
No input. Returns an output s32 '''MsecTime'''.
 
=== SetValueForSleepState ===
Takes an input u32 '''ValueForSleepState'''. No output.
 
=== GetMaxDebounceTime ===
No input. Returns an output u32 '''MaxDebounceTime'''.
 
=== SetDirectionInput ===
No input/output.
 
=== SetDirectionOutput ===
Takes an input u32 [[#GpioValue]]. No output.
 
= i2c, i2c:pcv =
This is "nn::i2c::IManager".
 
{| class="wikitable" border="1"
|-
|-
| 0x18 || 0xBD || X, 5 || || Out || [[HID services]]
! Cmd || Name
|-
|-
| 0x19 || 0xBE || X, 6 || Volume Up || In || [[Boot2]]
| 0 || [[#OpenSessionForDev_2|OpenSessionForDev]]
|-
|-
| 0x1A || 0xBF || X, 7 || Volume Down || In || [[Boot2]]
| 1 || [[#OpenSession_2|OpenSession]]
|-
|-
| 0x1B || 0xC0 || Y, 0 || Power supply monitor related. || In || [[PTM services]]
| 2 || [1.0.0-5.1.0] [[#HasDevice|HasDevice]]
|-
|-
| 0x1C || 0xC1 || Y, 1 || || ||
| 3 || [1.0.0-5.1.0] [[#HasDeviceForDev|HasDeviceForDev]]
|-
|-
| 0x1D || 0xA9 || V, 1 || || Out || [[NV services]]
| 4 || [6.0.0+] [[#OpenSession2_2|OpenSession2]]
|}
 
== OpenSessionForDev ==
Takes an input u16 '''SlaveAddress''' (padded to u32) and 3 input u32s '''BusIdx''', [[#AddressingMode]] and [[#SpeedMode]]. Returns an [[#II2cSession]].
 
== OpenSession ==
Takes an input [[#I2cDevice]]. Returns an output [[#II2cSession]].
 
== HasDevice ==
Takes an input [[#I2cDevice]]. Returns an output boolean success value.
 
== HasDeviceForDev ==
Takes an input u16 '''SlaveAddress''' (padded to u32) and 3 input u32s '''BusIdx''', [[#AddressingMode]] and [[#SpeedMode]]. Returns an output boolean success value.
 
== OpenSession2 ==
Same as [[#OpenSession_2|OpenSession]], but takes an input u32 [[#I2cDevice|DeviceCode]].
 
== II2cSession ==
This is "nn::i2c::ISession".
 
{| class="wikitable" border="1"
|-
|-
| 0x1E || 0xAA || V, 2 || || Out || [[NV services]]
! Cmd || Name
|-
|-
| 0x1F || 0x55 || K, 5 || Charger watchdog related. || Out || [[PTM services]]  
| 0 || [1.0.0-5.1.0] SendOld
|-
|-
| 0x20 || 0xAD || V, 5 || || ||
| 1 || [1.0.0-5.1.0] ReceiveOld
|-
|-
| 0x21 || 0xC8 || Z, 0 || Power supply monitor related. || In || [[PTM services]]  
| 2 || [1.0.0-5.1.0] ExecuteCommandListOld
|-
|-
| 0x22 || 0xCA || Z, 2 || || ||  
| 10 || [[#Send|Send]]
|-
|-
| 0x23 || 0xCB || Z, 3 || || ||  
| 11 || [[#Receive|Receive]]
|-
|-
| 0x24 || 0x4F || J, 7 || || ||  
| 12 || [[#ExecuteCommandList|ExecuteCommandList]]
|-
|-
| 0x25 || 0x50 || K, 0 || || ||
| 13 || [6.0.0+] [[#SetRetryPolicy_2|SetRetryPolicy]]
|}
 
== Send ==
Takes a type-0x21 input buffer '''InData''' and an input u32 [[#TransactionOption]]. No output.
 
== Receive ==
Takes a type-0x22 output buffer '''OutData''' and an input u32 [[#TransactionOption]]. No output.
 
== ExecuteCommandList ==
Takes a type-0x22 output buffer '''ReceiveBuffer''' and a type-0x9 input buffer '''CommandList'''. No output.
 
=== Commands ===
This is "nn::i2c::I2cCommand".
 
{| class=wikitable
! Bits || Name
|-
|-
| 0x26 || 0x51 || K, 1 || || ||  
| 0-5 || [[#CommandId]]
|-
|-
| 0x27 || 0x52 || K, 2 || || ||
| 6-7 || [[#TransactionOption]]
|}
 
A send command will write bytes to the device using the format: [u8 cmd_send] [u8 len] <bytes>
 
A receive command will read bytes from the device using the format: [u8 cmd_receive] [u8 len]
 
An extension sleep command will stall the device using the format: [u8 cmd_extension] [u8 ms]
 
== SetRetryPolicy ==
Takes 2 input u32s '''MaxRetries''' and '''RetryIntervalMicroSeconds'''. No output.
 
= uart =
This is "nn::uart::IManager".
 
{| class="wikitable" border="1"
|-
|-
| 0x28 || 0x54 || K, 4 || || ||  
! Cmd || Name
|-
|-
| 0x29 || 0x56 || K, 6 || || ||  
| 0 || [1.0.0-16.1.0] [[#HasPort|HasPort]]
|-
|-
| 0x2A || 0x57 || K, 7 || || ||  
| 1 || [1.0.0-16.1.0] [[#HasPortForDev|HasPortForDev]]
|-
|-
| 0x2B || 0x53 || K, 3 || || ||
| 2 || [1.0.0-16.1.0] [[#IsSupportedBaudRate|IsSupportedBaudRate]]
|-
|-
| 0x2C || 0xE3 || CC, 3 || || ||
| 3 || [1.0.0-16.1.0] [[#IsSupportedBaudRateForDev|IsSupportedBaudRateForDev]]
|-
|-
| 0x2D || 0x38 || H, 0 || || ||
| 4 || [1.0.0-16.1.0] [[#IsSupportedFlowControlMode|IsSupportedFlowControlMode]]
|-
|-
| 0x2E || 0x39 || H, 1 || || ||
| 5 || [1.0.0-16.1.0] [[#IsSupportedFlowControlModeForDev|IsSupportedFlowControlModeForDev]]
|-
|-
| 0x2F || 0x3B || H, 3 || || ||
| 6 || [[#CreatePortSession|CreatePortSession]]
|-
|-
| 0x30 || 0x3D || H, 5 || || ||
| 7 || [1.0.0-16.1.0] [[#IsSupportedPortEvent|IsSupportedPortEvent]]
|-
|-
| 0x31 || 0x3F || H, 7 || || ||
| 8 || [1.0.0-16.1.0] [[#IsSupportedPortEventForDev|IsSupportedPortEventForDev]]
|-
|-
| 0x32 || 0x40 || I, 0 || || Out || [[NV services]]
| 9 || [7.0.0-16.1.0] [[#IsSupportedDeviceVariation|IsSupportedDeviceVariation]]
|-
|-
| 0x33 || 0x41 || I, 1 || || Out || [[NV services]]
| 10 || [7.0.0-16.1.0] [[#IsSupportedDeviceVariationForDev|IsSupportedDeviceVariationForDev]]
|}
 
== HasPort ==
Takes an input [[#UartPort]]. Returns an output boolean success value.
 
== HasPortForDev ==
Takes an input [[#UartPortForDev]]. Returns an output boolean success value.
 
== IsSupportedBaudRate ==
Takes 2 input u32s [[#UartPort]] and '''BaudRate'''. Returns an output boolean success value.
 
Supported baud rates are 57600, 115200, 1000000 and 3000000.
 
== IsSupportedBaudRateForDev ==
Takes 2 input u32s [[#UartPortForDev]] and '''BaudRate'''. Returns an output boolean success value.
 
Supported baud rates are 57600, 115200, 1000000 and 3000000.
 
== IsSupportedFlowControlMode ==
Takes 2 input u32s [[#UartPort]] and [[#FlowControlMode]]. Returns an output boolean success value.
 
== IsSupportedFlowControlModeForDev ==
Takes 2 input u32s [[#UartPortForDev]] and [[#FlowControlMode]]. Returns an output boolean success value.
 
== CreatePortSession ==
No input. Returns an output [[#IPortSession]].
 
== IsSupportedPortEvent ==
Takes 2 input u32s [[#UartPort]] and [[#PortEventType]]. Returns an output boolean success value.
 
== IsSupportedPortEventForDev ==
Takes 2 input u32s [[#UartPortForDev]] and [[#PortEventType]]. Returns an output boolean success value.
 
== IsSupportedDeviceVariation ==
Takes 2 input u32s [[#UartPort]] and '''DeviceVariation'''. Returns an output boolean success value.
 
Supported device variations are 0 (Bluetooth) for UART-D, 0 (Joy-Con(R)) for UART-B, 0 (Joy-Con(L)) and 1 (SioMcu) for UART-C.
 
== IsSupportedDeviceVariationForDev ==
Takes 2 input u32s [[#UartPortForDev]] and '''DeviceVariation'''. Returns an output boolean success value.
 
Supported device variations are 0 (Bluetooth) for UART-D, 0 (Joy-Con(R)) for UART-B, 0 (Joy-Con(L)) and 1 (SioMcu) for UART-C.
 
== IPortSession ==
This is "nn::uart::IPortSession".
 
{| class="wikitable" border="1"
|-
|-
| 0x34 || 0x3E || H, 6 || || ||
! Cmd || Name
|-
|-
| 0x35 || 0xE2 || CC, 2 || || ||
| 0 || [[#OpenPort|OpenPort]]
|-
|-
| 0x36 || 0xE4 || CC, 4 || Battery event monitor related. || Out || [[PTM services]]
| 1 || [[#OpenPortForDev|OpenPortForDev]]
|-
|-
| 0x37 || 0x3A || H, 2 || || ||
| 2 || [[#GetWritableLength|GetWritableLength]]
|-
|-
| 0x38 || 0xC9 || Z, 1 || SDCard Card Detect || In || [[Filesystem services]]
| 3 || [[#Send_2|Send]]
|-
|-
| 0x39 || 0x4D || J, 5 || Charger watchdog related. || Out || [[PTM services]]
| 4 || [[#GetReadableLength|GetReadableLength]]
|-
|-
| 0x3A || 0x58 || L, 0 || Charger watchdog related. || Out || [[PTM services]]
| 5 || [[#Receive_2|Receive]]
|-
|-
| 0x3B || 0x3E || H, 6 || || ||
| 6 || [[#BindPortEvent|BindPortEvent]]
|-
|-
| 0x3C || 0x26 || E, 6 || || ||
| 7 || [[#UnbindPortEvent|UnbindPortEvent]]
|-
|-
| 0x3D || -1 || || || ||
| 8 || [14.0.0+] [[#OpenPort2|OpenPort2]]
|}
 
=== OpenPort ===
Takes 3 input u32s [[#UartPort]], '''BaudRate''' and [[#FlowControlMode]], 2 input u64s '''SendBufferLength''' and '''ReceiveBufferLength''' and 2 input TransferMemory handles '''SendHandle''' and '''ReceiveHandle'''. Returns an output boolean success value.
 
[6.0.0+] Takes 4 input u8s (padded as u32) '''IsInvertTx''', '''IsInvertRx''', '''IsInvertRts''' and '''IsInvertCts''', 3 input u32s [[#UartPort]], '''BaudRate''' and [[#FlowControlMode]], 2 input u64s '''SendBufferLength''' and '''ReceiveBufferLength''' and 2 input TransferMemory handles '''SendHandle''' and '''ReceiveHandle'''. Returns an output boolean success value.
 
[7.0.0+] Takes 4 input u8s (padded as u32) '''IsInvertTx''', '''IsInvertRx''', '''IsInvertRts''' and '''IsInvertCts''', 4 input u32s [[#UartPort]], '''BaudRate''', [[#FlowControlMode]] and '''DeviceVariation''', 2 input u64s '''SendBufferLength''' and '''ReceiveBufferLength''' and 2 input TransferMemory handles '''SendHandle''' and '''ReceiveHandle'''. Returns an output boolean success value.
 
This will Abort when the specified [[#UartPort]] is already being used, due to a [[SVC]] failing.
 
=== OpenPortForDev ===
Same as [[#OpenPort]], but takes an input [[#UartPortForDev]] instead.
 
=== GetWritableLength ===
No input. Returns an output u64 '''WritableLength'''.
 
=== Send ===
Takes a type-0x21 input buffer '''InData'''. Returns an output u64 size.
 
=== GetReadableLength ===
No input. Returns an output u64 '''ReadableLength'''.
 
=== Receive ===
Takes a type-0x22 output buffer '''OutData'''. Returns an output u64 size.
 
=== BindPortEvent ===
Takes an input u32 [[#PortEventType]] and an input s64 '''Threshold'''. Returns an output boolean success value and an Event handle with EventClearMode=0.
 
=== UnbindPortEvent ===
Takes an input u32 [[#PortEventType]]. Returns an output boolean success value.
 
=== OpenPort2 ===
Same as [[#OpenPort]], but takes an input u32 [[#UartPort|DeviceCode]] instead of an [[#UartPort]] and no longer returns an output boolean success value.
 
= pwm =
This is "nn::pwm::IManager".
 
{| class="wikitable" border="1"
|-
|-
| 0x3E || 0x33 || G, 3 || || ||
! Cmd || Name
|-
|-
| 0x3F || 0x1C || D, 4 || || ||
| 0 || OpenSessionForDev
|-
|-
| 0x40 || 0xD9 || BB, 1 || || ||
| 1 || OpenSession
|-
|-
| 0x41 || 0x0C || B, 4 || || ||
| 2 || [6.0.0+] [[#OpenSession2_3|OpenSession2]]
|}
 
== OpenSession2 ==
Takes a [[#ChannelName|DeviceCode]] and returns an [[#IChannelSession]].
 
== IChannelSession ==
This is "nn::pwm::IChannelSession".
 
{| class="wikitable" border="1"
|-
|-
| 0x42 || 0x0D || B, 5 || || ||
! Cmd || Name
|-
|-
| 0x43 || 0x21 || E, 1 || || ||
| 0 || SetPeriod
|-
|-
| 0x44 || 0x27 || E, 7 || || ||
| 1 || GetPeriod
|-
|-
| 0x45 || 0x92 || S, 2 || || ||
| 2 || [1.0.0-13.2.1] SetDuty
|-
|-
| 0x46 || 0x95 || S, 5 || || ||
| 3 || [1.0.0-13.2.1] GetDuty
|-
|-
| 0x47 || 0x98 || T, 0 || || ||
| 4 || SetEnabled
|-
|-
| 0x48 || 0x10 || C, 0 || || ||
| 5 || GetEnabled
|-
|-
| 0x49 || 0x11 || C, 1 || || Out || [[NV services]]
| 6 || [6.0.0+] [[#SetDutyCycle|SetDutyCycle]]
|-
|-
| 0x4A || 0x12 || C, 2 || || Out || [[NV services]]
| 7 || [6.0.0+] [[#GetDutyCycle|GetDutyCycle]]
|}
 
=== SetDutyCycle ===
Takes an input double '''DutyCycle'''. No output.
 
=== GetDutyCycle ===
No input. Returns an output double '''DutyCycle'''.
 
= pinmux =
This is "nn::pinmux::IManager".
 
{| class="wikitable" border="1"
|-
|-
| 0x4B || 0x42 || I, 2 || || ||
! Cmd || Name
|-
|-
| 0x4C || 0xE6 || CC, 6 || || ||
| 0 || [[#OpenSession_3|OpenSession]]
|}
|}


== OpenSessionForTest ==
== OpenSession ==
Same as [[#OpenSession]] but panics on failure.
Takes an [[#AssignablePinGroupName]] or an [[#AssignablePinGroupNameForHardwareTest]] and returns an [[#ISession|ISession]].


== IPadSession ==
== ISession ==
This is "nn::gpio::IPadSession".
This is "nn::pinmux::ISession".


{| class="wikitable" border="1"
{| class="wikitable" border="1"
Line 189: Line 451:
! Cmd || Name
! Cmd || Name
|-
|-
| 0 || SetDirection
| 0 || [[#SetPinAssignment|SetPinAssignment]]
|-
| 1 || [[#GetPinAssignment|GetPinAssignment]]
|-
|-
| 1 || GetDirection
| 2 || [[#SetPinAssignmentForHardwareTest|SetPinAssignmentForHardwareTest]]
|-
|-
| 2 || SetInterruptMode
| 3 || [17.0.0+] SetSfioConfiguration
|-
|-
| 3 || GetInterruptMode
| 4 || [17.0.0+] GetSfioConfiguration
|-
|-
| 4 || SetInterruptEnable
| 5 || [17.0.0+] SetInputEnableConfiguration
|-
|-
| 5 || GetInterruptEnable
| 6 || [17.0.0+] GetInputEnableConfiguration
|-
|-
| 6 || GetInterruptStatus
| 7 || [17.0.0+] SetPullConfiguration
|-
| 8 || [17.0.0+] GetPullConfiguration
|-
| 9 || [17.0.0+] SetPmConfiguration
|-
| 10 || [17.0.0+] GetPmConfiguration
|}
 
=== SetPinAssignment ===
Takes a [[#PinAssignment]]. No output.
 
=== GetPinAssignment ===
No input. Returns a [[#PinAssignment]].
 
=== SetPinAssignmentForHardwareTest ===
Takes a [[#PinAssignmentForHardwareTest]]. No output.
 
= sasbus =
This is "nn::sasbus::IManager".
 
This was added with [3.0.0+].
 
{| class="wikitable" border="1"
|-
|-
| 7 || ClearInterruptStatus
! Cmd || Name
|-
|-
| 8 || SetValue
| 0 || [[#OpenSession_4|OpenSession]]
|}
 
== OpenSession ==
Takes a [[#SasbusPort]] and returns an [[#ISession_2|ISession]].
 
== ISession ==
This is "nn::sasbus::ISession".
 
{| class="wikitable" border="1"
|-
|-
| 9 || GetValue
! Cmd || Name
|-
|-
| 10 || BindInterrupt
| 0 || [[#Send_3|Send]]
|-
|-
| 11 || UnbindInterrupt
| 1 || [[#Receive_3|Receive]]
|-
|-
| 12 || SetDebounceEnabled
| 2 || [[#StartPeriodicReceiveMode|StartPeriodicReceiveMode]]
|-
|-
| 13 || GetDebounceEnabled
| 3 || [[#StopPeriodicReceiveMode|StopPeriodicReceiveMode]]
|-
|-
| 14 || SetDebounceTime
| 4 || [19.0.0+]
|-
|-
| 15 || GetDebounceTime
| 5 || [19.0.0+]
|}
|}


== GpioPadDescriptor ==
=== Send ===
Takes a type-0x21 input buffer and an u8 '''SpiCommand'''. No output.
 
=== Receive ===
Takes a type-0x22 output buffer and an u8 '''SpiCommand'''. No output.
 
=== StartPeriodicReceiveMode ===
Takes an u8 '''SpiCommand''' (padded to u32), an u32, two u64s and a TransferMemory handle. No output.
 
[20.0.0+] Data intended for the user-process was [[Switch_System_Flaws|moved]] from tmem+0x8 to +0x0.
 
=== StopPeriodicReceiveMode ===
No input/output.
 
=== Cmd4 ===
Takes a total of 0x10-bytes of input and an input handle. No output.
 
This is similar to [[#StartPeriodicReceiveMode|StartPeriodicReceiveMode]]. This eventually calls an impl func which just writes some input fields into state, then (on NX) Aborts.
 
=== Cmd5 ===
No input/output.
 
This is identical to [[#StopPeriodicReceiveMode|StopPeriodicReceiveMode]].
 
= led =
This is "nn::led::detail::IManager".
 
This was added with [8.1.1+].
 
{| class="wikitable" border="1"
|-
! Cmd || Name
|-
| 0 || [[#OpenController|OpenController]]
|}
 
== OpenController ==
Takes a '''DeviceCode''' (which must be 0x35000065) and returns an [[#IController]] session for it.
 
== IController ==
This is "nn::led::detail::IController".
 
This was added with [8.1.1+].
 
{| class="wikitable" border="1"
|-
! Cmd || Name
|-
| 0 || StartLighting
|-
| 1 || StopLighting
|-
| 2 || SetLightingMode
|-
| 3 || GetLightingMode
|-
| 4 || IsLighting
|-
| 5 || SetRisingTime
|-
| 6 || GetRisingTime
|-
| 7 || SetFallingTime
|-
| 8 || GetFallingTime
|-
| 9 || SetPeakTime
|-
| 10 || GetPeakTime
|-
| 11 || SetPulseInterval
|-
| 12 || GetPulseInterval
|-
| 13 || SetPulseCount
|-
| 14 || GetPulseCount
|-
| 15 || GetMaxPulseCount
|-
| 16 || SetBreathInterval
|-
| 17 || GetBreathInterval
|-
| 18 || SetConstantBrightness
|-
| 19 || GetConstantBrightness
|-
| 20 || [10.0.0+] GetBreathingStatus ([8.1.1-9.2.0] RegisterPwmChannel)
|-
| 21 || [8.1.1-9.2.0] UnregisterPwmChannel
|}
 
= GpioPadName =
This is "nn::gpio::GpioPadName".
 
{| class="wikitable sortable" border="1"
|-
! Value || Name || [[#GpioPadDescriptor|GpioPadDescriptor]] || DeviceCode || Tegra (port, pin) || Description || Direction || Used by (services) || Used by (hardware)
|-
| 0x01 || CodecLdoEnTemp || 0xCC || 0x33000002 || Z, 4 || Audio Codec (ALC5639) Power || Out || [[Audio services]], [[Fatal services]] || Icosa, Hoag, Iowa, Aula
|-
| 0x02 || PowSdEn || 0x24 || 0x3C000001 || E, 4 || SdCard Power || Out || [[PCV services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x03 || BtRst || 0x3C || 0x37000002 || H, 4 || Bluetooth Reset || Out || [[Bluetooth Driver services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x04 || RamCode3 || 0xDA || 0xC9000402 || BB, 2 || Secondary Boot Device Configration || In || || Icosa, Iowa
|-
| 0x05 || GameCardReset || 0xDB || 0x3C000402 || BB, 3 || Gamecard Reset || Out || [[Filesystem services]] || Icosa, Copper, Hoag, Iowa, Aula
|-
| 0x06 || CodecAlert || 0xDC || 0x33000003 || BB, 4 || Audio Codec (ALC5639) Alert || In || [[Audio services]] || Icosa, Hoag, Iowa, Aula
|-
| 0x07 || PowGc || 0x25 || 0x3C000401 || E, 5 || Gamecard Power || Out || || Icosa, Copper
|-
| 0x08 || DebugControllerDet || 0x90 || 0x350000CA || S, 0 || Debug Pad Detect || In || [[HID services]] || Icosa, Iowa
|-
| 0x09 || BattChgStatus || 0x91 || 0x39000407 || S, 1 || Battery Charge Status || In || || Icosa, Hoag, Iowa, Aula
|-
| 0x0A || BattChgEnableN || 0x96 || 0x39000003 || S, 6 || Charger IC (BQ24193) Charge Enable || Out || [[PTM services]] || Icosa, Hoag, Iowa, Aula
|-
| 0x0B || FanTach || 0x97 || 0x3D000002 || S, 7 || Fan Tachometer || In || || Icosa, Hoag, Iowa, Calcio, Aula
|-
| 0x0C || ExtconDetS || 0x26 || 0x3500040B || E, 6 || Joy-Con(L) IsAttached (insertion, Joy-Con pin 5/console TX, pulled low on insert)  || In || [[HID services]], [[AM services]] || Icosa, Iowa, Aula
|-
| 0x0D || Vdd50AEn || 0x05 || 0x39000401 || A, 5 || Fan and Joy-Con 5V Power (Battery) || Out || [[PTM services]] || Icosa, Hoag, Iowa, Aula
|-
| 0x0E || SdevCoaxSel1 || 0x78 || 0xCA000406 ([1.0.0-10.0.0] 0xCA000402) || P, 0 || SDEV Coax Select || In || || Icosa, Iowa
|-
| 0x0F || GameCardCd || 0x93 || 0x3C000403 || S, 3 || Gamecard Card Detect || In || [[Filesystem services]], [[AM services]] || Icosa, Copper, Hoag, Iowa, Aula
|-
| 0x10 || ProdType0 || 0x7D || 0xC900040B || P, 5 || || In || || Icosa, Copper, Iowa
|-
| 0x11 || ProdType1 || 0x7C || 0xC900040C || P, 4 || || In || || Icosa, Copper, Iowa
|-
| 0x12 || ProdType2 || 0x7B || 0xC900040D || P, 3 || || In || || Icosa, Copper, Iowa
|-
| 0x13 || ProdType3 || 0x7A || 0xC900040E || P, 2 || || In || || Icosa, Copper, Iowa
|-
| 0x14 || TempAlert || 0xBC || 0x3E000002 || X, 4 || Temperature Sensor || In || || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x15 || CodecHpDetIrq || 0xAE || 0x33000004 || V, 6 || Audio Codec (ALC5639) Headphone Detect || In || [[Audio services]] || Icosa, Hoag, Iowa, Aula
|-
| 0x16 || MotionInt || 0xBA || 0x35000041 || X, 2 || Built-in IMU IRQ || In || || Icosa, Hoag, Iowa, Aula
|-
| 0x17 || TpIrq || 0xB9 || 0x35000036 || X, 1 || TouchPanel IRQ || In || [[HID services]] || Icosa, Hoag, Iowa, Aula
|-
| 0x18 || ButtonSleep2 || 0xBD || 0x35000001 || X, 5 || Power Button (Connected only on Hoag) || In || || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x19 || ButtonVolUp || 0xBE || 0x35000002 || X, 6 || Volume Up || In || [[Boot2]], [[Audio services]], [[Fatal services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x1A || ButtonVolDn || 0xBF || 0x35000003 || X, 7 || Volume Down || In || [[Boot2]], [[Audio services]] || Icosa, Copper, Hoag, Iowa, Calcio , Aula
|-
| 0x1B || BattMgicIrq || 0xC0 || 0x39000034 || Y, 0 || Fuel Gauge IC (MAX17050) IRQ || In || [[PTM services]], [[AM services]] || Icosa, Hoag, Iowa, Aula
|-
| 0x1C || RecoveryKey || 0xC1 || 0x35000004 || Y, 1 || Recovery Mode Key (HOME Button) || In || || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x1D || PowLcdBlEn || 0xA9 || 0x3400003E || V, 1 || LCD Backlight Power || Out || [[NV services]], [[Backlight services]] || Icosa, Hoag, Iowa
|-
| 0x1E || LcdReset || 0xAA || 0x34000033 || V, 2 || LCD Reset || Out || [[NV services]] || Icosa, Hoag, Iowa, Aula
|-
| 0x1F || PdVconnEn || 0x55 || 0x040000CC || K, 5 || USB-PD Controller (RHOM BM92T30MWV) VCONN Power || Out || [[PTM services]], [[USB services]] || Icosa, Hoag, Iowa, Aula
|-
| 0x20 || PdRstN || 0xAD || 0x040000CA || V, 5 || USB-PD Controller (RHOM BM92T30MWV) ResetN || Out || [[USB services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x21 || Bq24190Irq || 0xC8 || 0x39000002 || Z, 0 || Charger IC (BQ24193) IRQ || In || [[PTM services]], [[AM services]] || Icosa, Hoag, Iowa, Aula
|-
| 0x22 || SdevCoaxSel0 || 0xCA || 0xCA000405 ([1.0.0-10.0.0] 0xCA000401) || Z, 2 || SDEV Coax Select || In || || Icosa, Iowa
|-
| 0x23 || SdWp || 0xCB || 0x3C000003 || Z, 3 || SdCard Write Protect || In || || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x24 || TpReset || 0x4F || 0x35000035 || J, 7 || TouchPanel Reset || Out || [[HID services]] || Icosa, Hoag, Iowa, Aula
|-
| 0x25 || BtGpio2 || 0x50 || 0x37000401 || K, 0 || || In || || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x26 || BtGpio3 || 0x51 || 0x37000402 || K, 1 || || In || || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x27 || BtGpio4 || 0x52 || 0x37000403 || K, 2 || || In || || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x28 || CradleIrq || 0x54 || 0x040000CB || K, 4 || USB-PD Controller (RHOM BM92T30MWV) IRQ || In || [[USB services]], [[AM services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x29 || PowVcpuInt || 0x56 || 0x3E000003 || K, 6 || Sub-PMIC for CPU (MAX77621) IRQ || In || ||  Icosa, Copper, Aula
|-
| 0x2A || Max77621GpuInt || 0x57 || 0x3E000004 || K, 7 || Sub-PMIC for GPU (MAX77621) IRQ || In || || Icosa, Copper
|-
| 0x2B || ExtconChgU || 0x53 || 0x35000402 || K, 3 || Joy-Con(R) Charge || Out || [[HID services]] || Icosa, Iowa, Aula
|-
| 0x2C || ExtconChgS || 0xE3 || 0x3500040C || CC, 3 || Joy-Con(L) Charge || Out || [[HID services]] || Icosa, Iowa, Aula
|-
| 0x2D || WifiRfDisable || 0x38 || 0x38000003 || H, 0 || || Out || || Icosa, Copper, Hoag, Iowa, Calcio
|-
| 0x2E || WifiReset || 0x39 || 0x38000002 || H, 1 || WiFi Reset || Out || [[WLAN services]], [[PCIe services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x2F || ApWakeBt || 0x3B || 0x37000003 || H, 3 || Wake Bluetooth from Host || Out || [[Bluetooth Driver services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x30 || BtWakeAp || 0x3D || 0x37000004 || H, 5 || Wake Host from Bluetooth || In || [[AM services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x31 || BtGpio5 || 0x3F || 0x37000404 || H, 7 || || Out || || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x32 || PowLcdVddPEn || 0x40 || 0x34000034 || I, 0 || LCD Backlight PAVDD +5V || Out || [[NV services]] || Icosa, Hoag, Iowa
|-
| 0x33 || PowLcdVddNEn || 0x41 || 0x34000035 || I, 1 || LCD Backlight NAVDD -5V || Out || [[NV services]] || Icosa, Hoag, Iowa
|-
| 0x34 || ExtconDetU || 0x3E || 0x35000401 || H, 6 || Joy-Con(R) IsAttached (insertion, Joy-Con pin 5/console TX, pulled low on insert)  || In || [[HID services]], [[AM services]] || Icosa, Iowa, Aula
|-
| 0x35 || RamCode2 || 0xE2 || 0xC9000401 || CC, 2 || Secondary Boot Device Configration || In || || Icosa, Iowa
|-
| 0x36 || Vdd50BEn || 0xE4 || 0x39000402 || CC, 4 || Fan and Joy-Con 5V Power (USB) || Out || [[PTM services]] || Icosa, Iowa
|-
| 0x37 || WifiWakeHost || 0x3A || 0x38000004 || H, 2 || Wake Host from Wifi || In || [[AM services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x38 || SdCd || 0xC9 || 0x3C000002 || Z, 1 || SdCard Card Detect || In || [[Filesystem services]], [[AM services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 0x39 || OtgFet1ForSdev || 0x4D || 0x39000404 || J, 5 || Charger IC (BQ24193) OTG Charge Select || Out || [[PTM services]], [[USB services]] || Icosa, Iowa
|-
| 0x3A || OtgFet2ForSdev || 0x58 || 0x39000405 || L, 0 || Charger IC (BQ24193) OTG Charge Select || Out || [[PTM services]], [[USB services]] || Icosa, Iowa
|-
| 0x3B || ExtConWakeU || 0x3E || 0x35000403 || H, 6 || Joy-Con(R) Wake Detect || In || || Icosa, Hoag, Iowa, Aula
|-
| 0x3C || ExtConWakeS || 0x26 || 0x3500040D || E, 6 || Joy-Con(L) Wake Detect || In || || Icosa, Hoag, Iowa, Aula
|-
| 0x3D || PmuIrq || -1 || 0x39000406 || GIC 86 || Main PMIC IRQ (PMU_EXT IRQ) || || ||
|-
| 0x3E || ExtUart2Cts || 0x33 || 0x35000404 || G, 3 || Joy-Con(R) CTS (checked low) || In || [[HID services]], [[AM services]] ||
|-
| 0x3F || ExtUart3Cts || 0x1C || 0x3500040E || D, 4 || Joy-Con(L) CTS (checked low) || In || [[HID services]], [[AM services]] ||
|-
| 0x40 || 5VStepDownEn || 0xD9 || 0x39000408 || BB, 1 || 5V Step-Down Regulator Power || Out || || Copper
|-
| 0x41 || UsbSwitchB2Oc || 0x0C || 0x04000401 || B, 4 || USB Root Port 2 Over Current || In || [[USB services]] || Copper
|-
| 0x42 || 5VStepDownPg || 0x0D || 0x39000409 || B, 5 || 5V Step-Down Regulator Power Good Flag || In || || Copper
|-
| 0x43 || UsbSwitchAEn || 0x21 || 0x04000402 || E, 1 || USB Power || Out || [[USB services]] || Copper
|-
| 0x44 || UsbSwitchAFlag || 0x27 || 0x04000403 || E, 7 || USB Power Flag || In || [[USB services]] || Copper
|-
| 0x45 || UsbSwitchB3Oc || 0x92 || 0x04000404 || S, 2 || USB Root Port 3 Over Current || In || [[USB services]] || Copper
|-
| 0x46 || UsbSwitchB3En || 0x95 || 0x04000405 || S, 5 || USB Root Port 3 Power || Out || [[USB services]] || Copper
|-
| 0x47 || UsbSwitchB2En || 0x98 || 0x04000406 || T, 0 || USB Root Port 2 Power || Out || [[USB services]] || Copper
|-
| 0x48 || Hdmi5VEn || 0x10 || 0x34000004 || C, 0 || HDMI 5V Power || Out || [[NV services]] || Copper, Calcio
|-
| 0x49 || UsbSwitchB1En || 0x11 || 0x04000407 || C, 1 || USB Root Port 1 Power || Out || [[USB services]] || Copper, Calcio
|-
| 0x4A || HdmiPdTrEn || 0x12 || 0x34000005 || C, 2 || HDMI/Power Delivery Switch || Out || [[NV services]] || Copper, Calcio
|-
| 0x4B || FanEn || 0x42 || 0x3D000003 || I, 2 || Fan Power || Out || [[PTM services]] || Copper
|-
| 0x4C || UsbSwitchB1Oc || 0xE6 || 0x04000408 || CC, 6 || USB Root Port 1 Over Current || In || [[USB services]] || Copper, Calcio
|-
| [2.0.0+] 0x4D || PwmFan || 0xAC || 0x3D000001 || V, 4 || Pulse-Width Modulation Fan Control || Out || [[PTM services]] || Copper
|-
| [2.0.0+] 0x4E || HdmiHpd || 0xE1 || 0x34000006 || CC, 1 || HDMI Hot Plug Detect || In || [[NV services]] || Copper, Calcio
|-
| [5.0.0+] 0x4F || Max77812Irq || 0x56 || 0x3E000003 || K, 6 || Sub-PMIC (CPU/GPU/RAM) IRQ || In || || Hoag, Iowa, Calcio
|-
| [6.0.0+] 0x50 || Debug0 || 0x20 || 0xCA000001 || E, 0 || || Out || || Hoag, Calcio, Aula
|-
| [6.0.0+] 0x51 || Debug1 || 0x21 || 0xCA000002 || E, 1 || || Out || || Hoag, Calcio, Aula
|-
| [6.0.0+] 0x52 || Debug2 || 0x22 || 0xCA000003 || E, 2 || || Out || || Hoag, Calcio, Aula
|-
| [6.0.0+] 0x53 || Debug3 || 0x23 || 0xCA000004 || E, 3 || || Out || || Hoag, Calcio, Aula
|-
| [6.0.0+] 0x54 || NfcIrq || 0x4C || 0x36000004 || J, 4 || NFC Controller IRQ || In || [[NFC services]] || Hoag
|-
| [6.0.0+] 0x55 || NfcRst || 0x57 || 0x36000003 || K, 7 || NFC Controller Reset || Out || [[NFC services]] || Hoag
|-
| [6.0.0+] 0x56 || McuIrq || 0x27 ([6.0.0-8.0.0] 0x94) || 0x35000415 || E, 7 || Sio MCU IRQ || In || || Hoag
|-
| [6.0.0+] 0x57 || McuBoot || 0x98 || 0x35000416 || T, 0 || Sio MCU BOOT0 Select (0: Flash, 1: SRAM) || Out || [[HID services]] || Hoag
|-
| [6.0.0+] 0x58 || McuRst || 0x99 || 0x35000417 || T, 1 || Sio MCU ResetN (Output LOW -> Input) || In || [[HID services]] || Hoag
|-
| [6.0.0+] 0x59 || Vdd5V3En || 0xBB || 0x39000403 || X, 3 || OTG VBUS Power || Out || [[PTM services]] || Hoag, Iowa, Aula
|-
| [6.0.0+] 0x5A || McuPor || 0xE5 || 0x35000418 || CC, 5 || Sio MCU NPOR || Out || [[HID services]] || Hoag
|-
| [6.0.0+] 0x5B || (McuHome) || 0xAB || 0x35000005 || V, 3 || Sio MCU Home Button || In || [[HID services]], [[AM services]] || Hoag
|-
| [6.0.0+] 0x5C || NfcEn || 0x4E || 0x36000002 || J, 6 || NFC Controller Power || Out || [[NFC services]] || Hoag
|-
| [7.0.0+] - || ExtUart2Rts || 0x32 || 0x35000406 || G, 2 || Joy-Con(R) RTS || In || ||
|-
| [7.0.0+] - || ExtUart3Rts || 0x1B || 0x35000410 || D, 3 || Joy-Con(L) RTS || In || ||
|-
| [7.0.0+] - || || 0x17 || 0x3500041B || C, 7 || SPI4 MOSI (Built-in IMU, set as gpio-input so Sio can use IMU) || In || || Hoag
|-
| [7.0.0+] - || || 0x18 || 0x3500041C || D, 0 || SPI4 MISO (Built-in IMU, set as gpio-input so Sio can use IMU) || In || || Hoag
|-
| [7.0.0+] - || || 0x15 || 0x3500041D || C, 5 || SPI4 SCLK (Built-in IMU, set as gpio-input so Sio can use IMU) || In || || Hoag
|-
| [7.0.0+] - || || 0x16 || 0x3500041E || C, 6 || SPI4 CS0 (Built-in IMU, set as gpio-input so Sio can use IMU) || In || || Hoag
|-
| [10.0.0+] - || || 0xC5 || 0x35000065 || Y, 5 || Notification LED PWM (CLK 32K OUT) || Out || || Hoag
|-
| [10.0.0+] - || || 0x29 || 0x04000409 || F, 1 || || Out || || Calcio
|-
| [10.0.0+] - || || 0x38 || 0x34000401 || H, 0 || OLED Panel IRQ || In || [[Display services]] || Aula
|-
| [13.0.0+] - || (BtGpio6) || 0x46 || 0x37000405 || I, 6 || UART-D RTS (Bluetooth) || In || ||
|}
 
= GpioPadDescriptor =
{| class="wikitable" border="1"
{| class="wikitable" border="1"
|-
|-
Line 234: Line 835:
|}
|}


= i2c =
= Direction =
This is "nn::i2c::IManager".
This is "nn::gpio::Direction".
 
{| class="wikitable sortable" border="1"
|-
! Value || Name
|-
| 0 || Input
|-
| 1 || Output
|}
 
= GpioValue =
This is "nn::gpio::GpioValue".
 
{| class="wikitable sortable" border="1"
|-
! Value || Name
|-
| 0 || Low
|-
| 1 || High
|}
 
= InterruptMode =
This is "nn::gpio::InterruptMode".
 
{| class="wikitable sortable" border="1"
|-
! Value || Name
|-
| 0 || LowLevel
|-
| 1 || HighLevel
|-
| 2 || RisingEdge
|-
| 3 || FallingEdge
|-
| 4 || AnyEdge
|}
 
= InterruptStatus =
This is "nn::gpio::InterruptStatus".
 
{| class="wikitable sortable" border="1"
|-
! Value || Name
|-
| 0 || Inactive
|-
| 1 || Active
|}
 
= WakeBitFlag =
This is "nn::gpio::WakeBitFlag". This is a 128-bit flag.
 
= OpenMode =
This is "nn::gpio::OpenMode".
 
{| class="wikitable sortable" border="1"
|-
! Value || Name
|-
| 0 || None
|-
| 1 || Read
|-
| 2 || Write
|-
| 3 || ReadWrite
|}
 
= I2cDevice =
This is "nn::i2c::I2cDevice".
 
{| class="wikitable sortable" border="1"
|-
! Value || Name || DeviceCode || Port:Addr || Is10bit || Speed || Max Retries || Retry Delay || Description || Used by (services) || Used by (hardware)
|-
|  0 || ClassicController || 0x350000C9 || 0:52 || N || 100000 || 0 ||      0 || DebugPad Driver || [[HID services]] || Icosa, Iowa, Aula
|-
|  1 || Ftm3bd56 || 0x35000033 || 2:49 || N || 400000 || 0 ||      0 || TouchPanel || [[HID services]] || Icosa, Hoag, Iowa, Aula
|-
|  2 || Tmp451 || 0x3E000001 || 0:4C || N || 100000 || 0 ||      0 || Temperature Sensor || [[PTM services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
|  3 || Nct72 || 0x3E000001 || 0:4C || N || 100000 || 0 ||      0 || Temperature Sensor || [[PTM services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
|  4 || Alc5639 || 0x33000001 || 0:1C || N || 100000 || 0 ||      0 || Audio Codec || [[Audio services]], [[Fatal services]] || Icosa, Hoag, Iowa, Aula
|-
|  5 || Max77620Rtc || 0x3B000001 || 4:68 || N || 400000 || 3 || 5000000 || PMIC RTC || [[PCV services]] || Icosa, Copper
|-
|  6 || Max77620Pmic || 0x3A000001 || 4:3C || N || 400000 || 3 || 5000000 || PMIC || [[PCV services]] || Icosa, Copper
|-
|  7 || Max77621Cpu || 0x3A000003 || 4:1B || N || 400000 || 3 || 5000000 || Sub-PMIC for CPU || [[PCV services]] || Icosa, Copper
|-
|  8 || Max77621Gpu || 0x3A000004 || 4:1C || N || 400000 || 3 || 5000000 || Sub-PMIC for GPU || [[PCV services]] || Icosa, Copper
|-
|  9 || Bq24193 || 0x39000001 || 0:6B || N || 100000 || 3 || 5000000 || Charger IC || [[PTM services]] || Icosa, Hoag, Iowa, Aula
|-
| 10 || Max17050 || 0x39000033 || 0:36 || N || 100000 || 3 || 5000000 || Fuel Gauge IC || [[PTM services]], [[PCV services]] || Icosa, Hoag, Iowa, Aula
|-
| 11 || Bm92t30mwv || 0x040000C9 || 0:18 || N || 100000 || 3 || 5000000 || USB-PD controller || [[USB services]] || Icosa, Copper, Hoag, Iowa, Calcio, Aula
|-
| 12 || Ina226Vdd15v0Hb || 0x3F000401 || 1:40 || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| 13 || Ina226VsysCpuDs or Ina226VddCpuAp (SdevMariko) || 0x3F000001 || 1:41 || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| 14 || Ina226VsysGpuDs or Ina226VddGpuAp (SdevMariko) || 0x3F000002 || 1:44 || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| 15 || Ina226VsysDdrDs or Ina226VddDdr1V1Pmic (SdevMariko) || 0x3F000003 || 1:45 || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| 16 || Ina226VsysAp || 0x3F000402 || 1:46 || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| 17 || Ina226VsysBlDs || 0x3F000403 || 1:47 || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| 18 || Bh1730 || 0x35000047 || 1:29 || N || 400000 || 3 || 5000000 || Ambient Light Sensor || [[Backlight services]] || Icosa, Hoag, Iowa, Aula
|-
| 19 || Ina226VsysCore or Ina226VddCoreAp (SdevMariko) || 0x3F000404 || 1:48 || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| 20 || Ina226Soc1V8 or Ina226VddSoc1V8 (SdevMariko) || 0x3F000405 || 1:49 || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| 21 || Ina226Lpddr1V8 or Ina226Vdd1V8 (SdevMariko) || 0x3F000406 || 1:4A || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| 22 || Ina226Reg1V32 || 0x3F000407 || 1:4B || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| 23 || Ina226Vdd3V3Sys || 0x3F000408 || 1:4D || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| [2.0.0+] 24 || HdmiDdc || 0x34000001 || 3:50 || N || 100000 || 0 ||      0 || HDMI DDC || [[NV services]] || Copper, Calcio
|-
| [2.0.0+] 25 || HdmiScdc || 0x34000002 || 3:54 || N || 100000 || 0 ||      0 || HDMI SCDC || [[NV services]] || Copper, Calcio
|-
| [2.0.0+] 26 || HdmiHdcp || 0x34000003 || 3:3A || N || 100000 || 0 ||      0 || HDMI HDCP || [[NV services]] || Copper, Calcio
|-
| [4.0.0+] 27 || Fan53528 || 0x3A000005 || 4:52 ([4.0.0-8.0.0] 4:A4) || N || 400000 || 0 ||      0 || RAM Regulator (tied to Max77812Pmic) || || Hoag, Iowa, Calcio, Aula
|-
| [4.0.0+] 28 || Max77812Pmic || 0x3A000002 || 4:31 ([8.0.0-9.2.0] 4:33, [4.0.0-8.0.0] 4:31) || N || 400000 || 0 ||      0 || Sub-PMIC for CPU and GPU (tied to Fan53528) (Phase 31) || [[PCV services]] || Hoag, Iowa, Calcio, Aula
|-
| [4.0.0+] 29 || Max77812Pmic || 0x3A000006 ([4.0.0-9.2.0] 0x3A000002) || 4:33 ([4.0.0-8.0.0] 4:31) || N || 400000 || 0 ||      0 || Sub-PMIC for GPU, CPU and RAM (Phase 211) || [[PCV services]] || Hoag, Iowa, Calcio, Aula
|-
| [4.0.0+] 30 || Ina226VddDdr0V6 (SdevMariko) || 0x3F000409 || 1:4E || N || 400000 || 3 || 5000000 || Power Monitor || nvdbgsvc || Factory
|-
| [8.0.0+] 31 || (MillauNfc) || 0x36000001 || 1:08 || N || 400000 || 3 || 5000000 || NFC Controller || [[NFC services]] || Hoag
|-
| [12.0.0+] - || (Max77801) || 0x3A000007 || 4:18 || N || 400000 || 0 ||      0 || Audio Codec (ALC5639) Regulator || [[PCV services]] || Aula
|}
 
= AddressingMode =
This is "nn::i2c::AddressingMode".


{| class="wikitable" border="1"
{| class="wikitable sortable" border="1"
|-
! Value || Name
|-
|-
! Cmd || Name
| 0 || BitWidth7
|-
|-
| 0 || OpenSessionForDev
| 1 || BitWidth10
|}
 
= TransactionOption =
This is "nn::i2c::TransactionOption".
 
{| class="wikitable sortable" border="1"
|-
|-
| 1 || OpenSession
! Value || Name
|-
|-
| 2 || HasDevice
| 1 || StartCondition
|-
|-
| 3 || HasDeviceForDev
| 2 || StopCondition
|}
|}


== II2cSession ==
= SpeedMode =
This is "nn::i2c::ISession".
This is "nn::i2c::SpeedMode".


{| class="wikitable" border="1"
{| class="wikitable sortable" border="1"
|-
! Value || Name
|-
| 0x186A0 || Standard
|-
| 0x61A80 || Fast
|-
| 0xF4240 || FastPlus
|-
|-
! Cmd || Name
| 0x33E140 || HighSpeed
|}
 
= CommandId =
This is "nn::i2c::detail::CommandId".
 
{| class="wikitable sortable" border="1"
|-
|-
| 0 ||  
! Value || Name
|-
|-
| 1 ||  
| 0 || Send
|-
|-
| 2 ||  
| 1 || Receive
|-
|-
| 3 || Send
| 2 || Extension
|}
 
= SubCommandId =
This is "nn::i2c::detail::SubCommandId".
 
{| class="wikitable sortable" border="1"
|-
|-
| 4 || Receive
! Value || Name
|-
|-
| 5 || ExecuteCommandList
| 0 || Sleep
|}
|}


= i2c:pcv =
= UartPort =
{| class="wikitable" border="1"
This is "nn::uart::UartPort".
 
{| class="wikitable sortable" border="1"
|-
! Value || Name || DeviceCode (internal) || DeviceCode (mapped) || Description
|-
| 0 || UART-A || 0x03000001 || || Invalid
|-
|-
! Cmd || Name
| 1 || UART-D || 0x03000004 || 0x37000001 || Bluetooth
|-
|-
| 0 ||
| 2 || UART-B || 0x03000002 || 0x35000405 || Joy-Con(R)
|-
|-
| 1 ||
| 3 || UART-C || 0x03000003 || 0x3500040F || Joy-Con(L)
|-
|-
| 2 ||
| 4 || UART-C || 0x03000003 || 0x35000419 || SioMcu
|}
 
= UartPortForDev =
This is "nn::uart::UartPortForDev".
 
{| class="wikitable sortable" border="1"
|-
|-
| 10 ||
! Value || Name || DeviceCode (internal) || DeviceCode (mapped) || Description
|-
|-
| 11 ||
| 0 || UART-A || 0x03000001 || || Invalid
|-
|-
| 12 ||
| 1 || UART-B || 0x03000002 || 0x35000405 || Joy-Con(R)
|-
| 2 || UART-C || 0x03000003 || 0x3500040F || Joy-Con(L)
|-
| 3 || UART-D || 0x03000004 || 0x37000001 || Bluetooth
|}
|}


= uart =
= FlowControlMode =
This is "nn::uart::IManager".
This is "nn::uart::FlowControlMode".


{| class="wikitable" border="1"
{| class="wikitable sortable" border="1"
|-
! Value || Name
|-
| 0 || None
|-
|-
! Cmd || Name || Notes
| 1 || Hardware
|}
 
= PortEventType =
This is "nn::uart::PortEventType".
 
{| class="wikitable sortable" border="1"
|-
|-
| 0 || || Returns a u8/bool.
! Value || Name
|-
|-
| 1 || || Returns a u8/bool.
| 0 || SendBufferEmpty
|-
|-
| 2 || || Returns a u8/bool.
| 1 || SendBufferReady
|-
|-
| 3 || || Returns a u8/bool.
| 2 || ReceiveBufferReady
|-
|-
| 4 || || Takes marshalled arguments.
| 3 || ReceiveEnd
|}
 
= ChannelName =
This is "nn::pwm::ChannelName".
 
{| class="wikitable sortable" border="1"
|-
|-
| 5 || || Takes marshalled arguments.
! Value || Name || DeviceCode || Description || Used by
|-
|-
| 6 || GetIPortSession ||
| 0 || Invalid || || ||
|-
|-
| 7 || ||  
| 1 || CpuFan || 0x3D000001 || PWM Channel 1 || [[PTM_services#fan|PTM services]]
|-
|-
| 8 || ||  
| 2 || LcdBacklight || 0x3400003D || PWM Channel 0 || [[Backlight services]], [[NV services]]
|-
|-
| 3 || Led || 0x35000065 || PMC LED Soft Blink || [[Bus services#led|Bus services]]
|}
|}


== IPortSession ==
= AssignablePinGroupName =
This is "nn::uart::IPortSession".
This is "nn::pinmux::AssignablePinGroupName".


{| class="wikitable" border="1"
{| class="wikitable sortable" border="1"
|-
! Value || Description
|-
|-
! Cmd || Name || Notes
| 0 || ExtConUartB
|-
|-
| 0 || || Takes marshalled arguments
| 1 || ExtConUartC
|-
|-
| 1 || || Takes marshalled arguments
| 2 || Sdmmc1
|-
|-
| 2 || ||  
| 3 || PwmFan
|-
|-
| 3 || || Takes marshalled arguments
| 100 || Invalid
|}
 
= AssignablePinGroupNameForHardwareTest =
This is "nn::pinmux::AssignablePinGroupNameForHardwareTest".
 
{| class="wikitable sortable" border="1"
|-
|-
| 4 || || Returns 2x u64. Both zero.
! Value || Description
|-
|-
| 5 || ||  
| 0 || Invalid
|-
|-
| 6 || ||  
| 1 || Invalid
|-
|-
| 7 || ||  
| 2 || Invalid
|-
|-
| 3 || Invalid
|-
| 100 || UartD
|}
|}


= pwm =
= PinAssignment =
This is "nn::pwm::IManager".
This is "nn::pinmux::PinAssignment".


{| class="wikitable" border="1"
{| class="wikitable sortable" border="1"
|-
! Value || Name
|-
| 0 || ExtConUartOutputEnable
|-
| 1 || ExtConUartOutputHiZ
|-
| 2 || Sdmmc1OutputHigh
|-
| 3 || Sdmmc1ResetState
|-
| 4 || Sdmmc1SchmtEnable
|-
|-
! Cmd || Name
| 5 || Sdmmc1SchmtDisable
|-
|-
| 0 || OpenSessionForDev
| 6 || PwmFanEnable
|-
|-
| 1 || OpenSession
| 7 || PwmFanHiZ
|}
|}


== IChannelSession ==
= PinAssignmentForHardwareTest =
This is "nn::pwm::IChannelSession".
This is "nn::pinmux::PinAssignmentForHardwareTest".


{| class="wikitable" border="1"
{| class="wikitable sortable" border="1"
|-
|-
! Cmd || Name
! Value || Name
|-
|-
| 0 || SetPeriod
| 100 || UartDHiZ
|-
|-
| 1 || GetPeriod
| 101 || UartDEnable
|}
 
= SasbusPort =
{| class="wikitable sortable" border="1"
|-
|-
| 2 || SetDuty
! Value || Name || DeviceCode || Description
|-
|-
| 3 || GetDuty
| 0 || SPI4 || 0x3500003D || Lsm6ds3 (WHOAMI 0x69, 0x6A and 0x6C)
|-
|-
| 4 || SetEnabled
| [10.0.0+] 1 || SPI4 || 0x3500003D || Icm40607 (WHOAMI 0x38)
|-
|-
| 5 || GetEnabled
| [13.0.0+] 2 || SPI4 || 0x3500003D || Icm42607p (WHOAMI 0x60)
|}
|}
[[Category:Services]]
Retrieved from "https://switchbrew.org/wiki/Bus_services"