Bus services

gpio

This is "nn::gpio::IManager".

Cmd	Name
0	#OpenSessionForDev
1	#OpenSession
2	#OpenSessionForTest
3	IsWakeEventActive
4	GetWakeEventActiveFlagSet
5	SetWakeEventActiveFlagSetForDebug
6	SetWakePinDebugMode
7	[5.0.0+] #OpenSession2
8	[5.0.0+] IsWakeEventActive2
9	[5.0.0+] SetWakeEventActiveFlagSetForDebug2

Known Devices

GpioPadName	GpioPadDescriptor	Tegra (port, pin)	Usage	Direction	Used by
0x01	0xCC	Z, 4	Audio Codec (ALC5639) Power	Out	Icosa, Hoag, [5.0.0+] Mariko (Audio services, Fatal services)
0x02	0x24	E, 4	SDCard Power	Out	Icosa, Copper, Hoag, [5.0.0+] Mariko (Filesystem services)
0x03	0x3C	H, 4	BT_RST_PH4	Out	Icosa, Copper, Hoag, [5.0.0+] Mariko (Bluetooth Driver services)
0x04	0xDA	BB, 2		In	Icosa, Hoag, [5.0.0+] Mariko
0x05	0xDB	BB, 3	GcAsic Power	Out	Icosa, Copper, Hoag, [5.0.0+] Mariko (Filesystem services)
0x06	0xDC	BB, 4	Headphone Detect	In	Icosa, Hoag, [5.0.0+] Mariko (Audio services)
0x07	0x25	E, 5		Out	Icosa, Copper, Hoag
0x08	0x90	S, 0	DebugPadDriver	In	Icosa, Hoag, [5.0.0+] Mariko (HID services)
0x09	0x91	S, 1		In	Icosa, Hoag, [5.0.0+] Mariko
0x0A	0x96	S, 6	Charger IC (BQ24193) Charge Enable	Out	Icosa, Hoag, [5.0.0+] Mariko (PTM services)
0x0B	0x97	S, 7	CPU fan sampling	In	Icosa, Hoag, [5.0.0+] Mariko
0x0C	0x26	E, 6	Joy-Con(L) IsAttached (insertion, Joy-Con pin 5/console TX, pulled low on insert?)	In	Icosa, Hoag, [5.0.0+] Mariko (HID services)
0x0D	0x05	A, 5	Fan enable (normal)	Out	Icosa, Hoag, [5.0.0+] Mariko (PTM services)
0x0E	0x78	P, 0	SDMMC3_CLK_PP0?	In	Icosa, Hoag, [5.0.0+] Mariko
0x0F	0x93	S, 3	GcAsic IRQ	In	Icosa, Copper, Hoag, [5.0.0+] Mariko (Filesystem services)
0x10	0x7D	P, 5	SDMMC3_DAT0_PP5?	In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x11	0x7C	P, 4	SDMMC3_DAT1_PP4?	In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x12	0x7B	P, 3	SDMMC3_DAT2_PP3?	In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x13	0x7A	P, 2	SDMMC3_DAT3_PP2?	In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x14	0xBC	X, 4	Temperature Sensor	In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x15	0xAE	V, 6		In	Icosa, Hoag, [5.0.0+] Mariko (Audio services)
0x16	0xBA	X, 2	MOTION_INT_PX2?	In	Icosa, Hoag, [5.0.0+] Mariko
0x17	0xB9	X, 1	TouchPanel IRQ (TOUCH_INT_PX1) (unused - polled instead)	In	Icosa, Hoag, [5.0.0+] Mariko (HID services)
0x18	0xBD	X, 5	Power Button (BUTTON_POWER_ON_PX5)	In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x19	0xBE	X, 6	Volume Up (BUTTON_VOL_UP_PX6)	In	Icosa, Copper, Hoag, [5.0.0+] Mariko (Boot2, Audio services)
0x1A	0xBF	X, 7	Volume Down (BUTTON_VOL_DOWN_PX7)	In	Icosa, Copper, Hoag, [5.0.0+] Mariko (Boot2, Audio services)
0x1B	0xC0	Y, 0	Fuel Gauge IC (MAX17050) IRQ	In	Icosa, Hoag, [5.0.0+] Mariko (PTM services)
0x1C	0xC1	Y, 1	BUTTON_HOME_PY1	In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x1D	0xA9	V, 1	Backlight Enable (LCD_BL_EN_PV1)	Out	Icosa, Hoag, [5.0.0+] Mariko (NV services, Backlight services)
0x1E	0xAA	V, 2	Backlight Reset (LCD_RST_PV2)	Out	Icosa, Hoag, [5.0.0+] Mariko (NV services)
0x1F	0x55	K, 5	Charger IC (BQ24193) OTG charge select	Out	Icosa, Hoag, [5.0.0+] Mariko (PTM services, USB services)
0x20	0xAD	V, 5	USB-PD controller (RHOM BM92T30MWV) related	Out	Icosa, Copper, Hoag, [5.0.0+] Mariko (USB services)
0x21	0xC8	Z, 0	Charger IC (BQ24193) IRQ	In	Icosa, Hoag, [5.0.0+] Mariko (PTM services)
0x22	0xCA	Z, 2		In	Icosa, Hoag, [5.0.0+] Mariko
0x23	0xCB	Z, 3		In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x24	0x4F	J, 7	TouchPanel reset	Out	Icosa, Hoag, [5.0.0+] Mariko (HID services)
0x25	0x50	K, 0		In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x26	0x51	K, 1		In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x27	0x52	K, 2		In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x28	0x54	K, 4	USB-PD controller (RHOM BM92T30MWV) IRQ	In	Icosa, Copper, Hoag, [5.0.0+] Mariko (USB services)
0x29	0x56	K, 6		In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x2A	0x57	K, 7		In	Icosa, Copper, Hoag
0x2B	0x53	K, 3	Joy-Con(R) NwcpDriver1.NwcpCharger	Out	Icosa, Hoag, [5.0.0+] Mariko (HID services)
0x2C	0xE3	CC, 3	Joy-Con(L) NwcpDriver0.NwcpCharger	Out	Icosa, Hoag, [5.0.0+] Mariko (HID services)
0x2D	0x38	H, 0	WIFI_EN_PH0?	Out	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x2E	0x39	H, 1	WIFI_RST_PH1	Out	Icosa, Copper, Hoag, [5.0.0+] Mariko (Wlan services, PCIe services)
0x2F	0x3B	H, 3	AP_WAKE_BT_PH3	Out	Icosa, Copper, Hoag, [5.0.0+] Mariko (Bluetooth Driver services)
0x30	0x3D	H, 5		In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x31	0x3F	H, 7		Out	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x32	0x40	I, 0	Backlight +5V	Out	Icosa, Hoag, [5.0.0+] Mariko (NV services)
0x33	0x41	I, 1	Backlight -5V	Out	Icosa, Hoag, [5.0.0+] Mariko (NV services)
0x34	0x3E	H, 6	Joy-Con(R) IsAttached (insertion, Joy-Con pin 5/console TX, pulled low on insert?)	In	Icosa, Hoag, [5.0.0+] Mariko (HID services)
0x35	0xE2	CC, 2		In	Icosa, Hoag, [5.0.0+] Mariko
0x36	0xE4	CC, 4	Fan enable (high power)	Out	Icosa, Hoag, [5.0.0+] Mariko (PTM services)
0x37	0x3A	H, 2		In	Icosa, Copper, Hoag, [5.0.0+] Mariko
0x38	0xC9	Z, 1	SDCard Card Detect	In	Icosa, Copper, Hoag, [5.0.0+] Mariko (Filesystem services)
0x39	0x4D	J, 5	Charger IC (BQ24193) OTG charge select	Out	Icosa, Hoag, [5.0.0+] Mariko (PTM services, USB services)
0x3A	0x58	L, 0	Charger IC (BQ24193) OTG charge select	Out	Icosa, Hoag, [5.0.0+] Mariko (PTM services, USB services)
0x3B	0x3E	H, 6	Joy-Con(R) NwcpDriver1.GpioMonitorTask0 duplicate?	In	Icosa, Hoag, [5.0.0+] Mariko
0x3C	0x26	E, 6	Joy-Con(L) NwcpDriver1.GpioMonitorTask0 duplicate?	In	Icosa, Hoag, [5.0.0+] Mariko
0x3D	-1
0x3E	0x33	G, 3	Joy-Con(R) CTS (checked low)	In	None (HID services)
0x3F	0x1C	D, 4	Joy-Con(L) CTS (checked low)	In	None (HID services)
0x40	0xD9	BB, 1		Out	[2.0.0+] Copper
0x41	0x0C	B, 4	Lid Closed (unused)	In	[2.0.0+] Copper
0x42	0x0D	B, 5		In	[2.0.0+] Copper
0x43	0x21	E, 1	USB power	Out	[2.0.0+] Copper (USB services)
0x44	0x27	E, 7		In	[2.0.0+] Copper
0x45	0x92	S, 2		In	[2.0.0+] Copper
0x46	0x95	S, 5	USB root port 4 power	Out	[2.0.0+] Copper (USB services)
0x47	0x98	T, 0	USB root port 3 power	Out	[2.0.0+] Copper (USB services)
0x48	0x10	C, 0	HdmiHotplug	Out	[2.0.0+] Copper (NV services)
0x49	0x11	C, 1	USB root port 2 power	Out	[2.0.0+] Copper (USB services)
0x4A	0x12	C, 2	HdmiHotplug	Out	[2.0.0+] Copper (NV services)
0x4B	0x42	I, 2		Out	[2.0.0+] Copper
0x4C	0xE6	CC, 6		In	[2.0.0+] Copper
[2.0.0+] 0x4D	0xAC	V, 4		Out	[2.0.0+] Copper
[2.0.0+] 0x4E	0xE1	CC, 1	HdmiHotplug (HDMI_INT_DP_HPD_PCC1)	In	[2.0.0+] Copper (NV services)
[5.0.0+] 0x4F	0x56	K, 6			None
-	0x32	G, 2	Joy-Con(R) RTS		None
-	0x1B	D, 3	Joy-Con(L) RTS		None

GpioPadDescriptor

Bits	Description
7-5	Controller index
4-3	Port index
2-0	Pin number

OpenSessionForDev

Takes a raw #GpioPadDescriptor and returns a #IPadSession session for it.

OpenSession

Same thing as #OpenSessionForDev except it takes a GpioPadName which is then converted to a #GpioPadDescriptor. Returns an #IPadSession session.

OpenSessionForTest

Same as #OpenSession but panics on failure.

OpenSession2

Same as #OpenSession but takes a DeviceCode instead of a GpioPadName.

IPadSession

This is "nn::gpio::IPadSession".

Cmd	Name
0	SetDirection
1	GetDirection
2	SetInterruptMode
3	GetInterruptMode
4	SetInterruptEnable
5	GetInterruptEnable
6	GetInterruptStatus
7	ClearInterruptStatus
8	SetValue
9	GetValue
10	BindInterrupt
11	UnbindInterrupt
12	SetDebounceEnabled
13	GetDebounceEnabled
14	SetDebounceTime
15	GetDebounceTime
16	[4.0.0+] SetValueForSleepState

i2c, i2c:pcv

This is "nn::i2c::IManager".

Cmd	Name
0	OpenSessionForDev
1	OpenSession
2	HasDevice
3	HasDeviceForDev

Known Devices

I2cDevice	Port:Addr	Is10bit	Speed	Max Retries	Retry Delay	Usage	Used by
0	0:52	N	100000	0	0	DebugPadDriver	HID services
1	2:49	N	400000	0	0	TouchPanel	HID services
2	0:4c	N	100000	0	0	Temperature Sensor (TMP451 or NCT72)	PTM services
3	0:4c	N	100000	0	0	Temperature Sensor (TMP451 or NCT72) (duplicate)
4	0:1c	N	100000	0	0	Audio Codec (ALC5639)	Audio services, Fatal services
5	4:68	N	400000	3	5000000	PMIC RTC (max77620_rtc0), max77620_irq0	PCV services
6	4:3c	N	400000	3	5000000	PMIC (MAX77620), max77620_irq0	PCV services
7	4:1b	N	400000	3	5000000	Sub-PMIC for CPU (max77621_cpu)	PCV services
8	4:1c	N	400000	3	5000000	Sub-PMIC for GPU (max77621_gpu)	PCV services
9	0:6b	N	100000	3	5000000	Charger IC (BQ24193)	PTM services
10	0:36	N	100000	3	5000000	Fuel Gauge IC (MAX17050)	PCV services, PTM services
11	0:18	N	100000	3	5000000	USB-PD controller (RHOM BM92T30MWV)	USB services
12	1:40	N	400000	3	5000000	Power Monitor (ina226_V_VDD15V0-HB)	Factory testing
13	1:41	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-CPU-DS)	Factory testing
14	1:44	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-GPU-DS)	Factory testing
15	1:45	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-DDR-DS)	Factory testing
16	1:46	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-AP)	Factory testing
17	1:47	N	400000	3	5000000	Power Monitor (ina226_V_VSYS-BL-DS)	Factory testing
18	1:29	N	400000	3	5000000	Ambient Light Sensor (BH1730)	Backlight services
19	1:48	N	400000	3	5000000	Power Monitor (ina226_CORE)	Factory testing
20	1:49	N	400000	3	5000000	Power Monitor (ina226_Soc-1V8)	Factory testing
21	1:4a	N	400000	3	5000000	Power Monitor (ina226_LPDDR4-1V8)	Factory testing
22	1:4b	N	400000	3	5000000	Power Monitor (ina226_REG1V32)	Factory testing
23	1:4d	N	400000	3	5000000	Power Monitor (ina226_VDD3V3-SYS)	Factory testing
24	3:50	N	100000	0	0	HDMI DDC	NV services
25	3:54	N	100000	0	0	HDMI SCDC	NV services
26	3:3a	N	100000	0	0	DisplayHdmiHotplugHandler	NV services

OpenSessionForDev

Takes an u32 port, an u16 addr, an AddressingMode (1 for 10-bit, 0 otherwise) and a SpeedMode (400000 or 100000). Returns a #II2cSession session.

OpenSession

Takes an I2cDevice and returns a #II2cSession session for it.

HasDevice

Takes an I2cDevice and returns true if the device exists or false otherwise.

HasDeviceForDev

Takes an u32 port, an u16 addr, an AddressingMode (1 for 10-bit, 0 otherwise) and a SpeedMode (400000 or 100000). Returns true if the device exists or false otherwise.

II2cSession

This is "nn::i2c::ISession".

Cmd	Name
0	Send
1	Receive
2	ExecuteCommandList
10	SendAuto
11	ReceiveAuto
12	ExecuteCommandListAuto

uart

This is "nn::uart::IManager".

Cmd	Name
0	#DoesUartExist
1	DoesUartExistForTest
2	#SetUartBaudrate
3	SetUartBaudrateForTest
4	#IsSomethingUartValid
5	IsSomethingUartValidForTest
6	#GetSession
7	IsSomethingUartValid2
8	IsSomethingUartValid2ForTest

DoesUartExist

Takes a u32 #UartPort and returns boolean success value

SetUartBaudrate

Takes a u32 #UartPort and a u32 baudrate and returns boolean success value

IsSomethingUartValid

Takes a u32 #UartPort and returns boolean success value

GetSession

Takes a u32 #UartPort and returns an #IPortSession

UartPort

Name	Port	Usage
1	UART-D	Bluetooth
2	UART-B	Joy-Con(R)
3	UART-C	Joy-Con(L)

IPortSession

This is "nn::uart::IPortSession".

Cmd	Name
0	OpenSession
1	OpenSessionForTest
2
3
4
5
6
7

Port Mapping

OpenSession translates user IDs to to the #UartPort index.

OpenSessionForTest takes the port index verbatim.

pwm

This is "nn::pwm::IManager".

Cmd	Name
0	OpenSessionForDev
1	OpenSession

Known Channels

Name	Interface	Usage	Used by
1	PWM Channel 1	Fan	PTM services
2	PWM Channel 0	Backlight	Backlight services, NV services
3	PMC Blinker

IChannelSession

This is "nn::pwm::IChannelSession".

Cmd	Name
0	SetPeriod
1	GetPeriod
2	SetDuty
3	GetDuty
4	SetEnabled
5	GetEnabled

pinmux

This is "nn::pinmux::IManager".

Cmd	Name
0	OpenSession

ISession

This is "nn::pinmux::ISession".

Cmd	Name
0	SetPinAssignment
1	GetPinAssignment
2	SetPinAssignmentForHardwareTest

sasbus

This is "nn::sasbus::IManager".

Cmd	Name
0	OpenSession

ISession

This is "nn::sasbus::ISession".

Cmd	Name
0
1
2
3