Package1

Present in the firmware package titles (0100000000000819, 010000000000081A, 010000000000081B and 010000000000081C) and installed into eMMC storage's boot partitions 0 and 1, "package1" contains the first Switch bootloader ("Package1ldr") to run under the NVIDIA boot processor (an ARM7TDMI called "BPMP", "BPMP-Lite", "AVP" or "COP"), as well as the actual encrypted package1 ("PK11") blob containing the second Switch Bootloader and TrustZone code.

The boot ROM validates, copies to IRAM and executes this package by parsing it's information block from the BCT.

Format

This package is distributed as a plaintext initial bootloader (package1ldr) and a secondary encrypted blob ("PK11"). Execution starts at plaintext package1ldr which will set up hardware, generate keys and decrypt the next stage.

Package1ldr

The code for this stage is stored in plaintext inside the package. By looking into the BCT's bootloader0_info (normal) or bootloader1_info (safe mode), the boot ROM starts executing this stage at address 0x40010020 in IRAM.

Initialization

The stack pointer is set.

 // Set the stack pointer
 *(u32 *)sp = 0x40008000;
 
 // Jump to main
 bootloader_main();
 
 // Infinite loop
 deadlock();

Main

The bootloader poisons the exception vectors, cleans up memory (.bss and init_array), sets up hardware devices (including the security engine and fuses), does all the necessary checks, generates keys and finally decrypts and executes the next stage.

 // Poison all exception vectors
 *(u32 *)0x6000F200 = panic();
 *(u32 *)0x6000F204 = panic();
 *(u32 *)0x6000F208 = panic();
 *(u32 *)0x6000F20C = panic();
 *(u32 *)0x6000F210 = panic();
 *(u32 *)0x6000F214 = panic();
 *(u32 *)0x6000F218 = panic();
 *(u32 *)0x6000F21C = panic();
 
 u32 bss_addr_end = bss_addr_start;
 u32 bss_offset = 0;
 u32 bss_size = bss_addr_end - bss_addr_start;
 
 // Clear .bss region
 // Never happens due to bss_size being set to 0
 while (bss_offset < bss_size)
 {
    *(u32 *)bss_addr_start + bss_offset = 0;
    bss_offset += 0x04;
 }
 
 u32 init_array_addr_end = init_array_addr_start;
 u32 init_array_offset = init_array_addr_start;
 
 // Call init methods
 // Never happens due to init_array_addr_end being set to init_array_addr_start
 while (init_array_offset < init_array_addr_end)
 {
    u32 init_method_offset = *(u32 *)init_array_offset;
 
    call_init_method(init_method_offset + init_array_offset);
    init_array_offset += 0x04;
 }
 
 // Setup I2S1, I2S2, I2S3, I2S4, DISPLAY and VIC
 enable_hw_devices();
 
 // Program the SE clock and resets
 // Uses RST_DEVICES_V, CLK_OUT_ENB_V, CLK_SOURCE_SE and CLK_V_SE
 enable_se_clkrst();
 
 // Set MISC_CLK_ENB
 // This makes fuse registers visible
 enable_misc_clk(0x01);
 
 // Read FUSE_SKU_INFO and compare with 0x83
 check_sku();
 
 // Check configuration fuses
 check_config_fuses();
 
 u32 bct_iram_addr = 0x40000000;
 
 // Check bootloader version from BCT
 check_bootloader_ver(bct_iram_addr);
 
 // Check anti-downgrade fuses
 check_downgrade();
 
 // Set FUSE_DIS_PGM
 // Disables fuse programming until next reboot
 disable_fuse_pgm();
 
 // Setup memory controllers
 enable_mem_ctl();
 
 // Setup the security engine's address
 set_se_addr(0x70012000);
 
 // Check SE global config
 check_se_status();
 
 // Generate keys
 keygen(bct_iram_addr);
 
 u32 pk11_blob_addr = 0x40013FE0;
 
 // Decrypt the PK11 blob and get the next stage's entrypoint
 nx_boot_addr = decrypt_pk11_blob(pk11_blob_addr);
 
 u32 nx_boot_sp = 0x40007000;
 
 // Set the stack pointer and jump to a stub responsible
 // for cleaning up and branching into the next stage
 exec_nx_boot_stub(nx_boot_addr, nx_boot_stub_addr, nx_boot_sp);
 
 return;

Panic

If a panic occurs, all sensitive memory contents are cleared, the security engine and fuse programming are disabled and the boot processor is left in a halted state.

 // Clear all stack contents
 clear_stack();
 
 // Terminate the security engine
 disable_se();
 
 // Set FUSE_DIS_PGM
 // Disables fuse programming until next reboot
 disable_fuse_pgm();
 
 // Clear temporary key storage memory
 clear_mem();
 
 // Clear the PK11 blob from memory
 clear_pk11_blob();
 
 u32 FLOW_CTLR_HALT_COP_EVENTS = 0x60007004;
 u32 FLOW_MODE_STOP = 0x40000000;
 u32 HALT_COP_EVENT_JTAG = 0x10000000;
 
 // Halt the boot processor
 while (true)
    *(u32 *)FLOW_CTLR_HALT_COP_EVENTS = (FLOW_MODE_STOP | HALT_COP_EVENT_JTAG);

Anti-downgrade

See Anti-downgrade.

Memory controllers

After disabling fuse programming, the bootloader configures the EMC and MEM/MC. It additionally disables QSPI resets and programs a special aperture designed for AHB redirected access to IRAM.

 u32 PERIPH_CLK_SOURCE_EMC = 0x6000619C;
 u32 CLK_OUT_ENB_SET_H = 0x60006328;
 u32 CLK_OUT_ENB_SET_X = 0x60006284;
 u32 RST_DEVICES_SET_H = 0x60006308;
 u32 RST_DEVICES_CLR_Y = 0x600062AC;
 u32 MC_IRAM_REG_CTRL = 0x70019964;
 u32 MC_IRAM_BOM = 0x7001965C;
 u32 MC_IRAM_TOM = 0x70019660;
 
 // Initialize EMC's clock source
 u32 emc_clk_src_val = *(u32 *)PERIPH_CLK_SOURCE_EMC;
 *(u32 *)PERIPH_CLK_SOURCE_EMC = (emc_clk_src_val | 0x40000000);
 
 // Enable CLK_H_EMC
 u32 clk_out_enb_h_val = *(u32 *)CLK_OUT_ENB_SET_H;
 clk_out_enb_h_val &= ~(0x2000000);
 clk_out_enb_h_val |= 0x2000000;
 *(u32 *)CLK_OUT_ENB_SET_H = clk_out_enb_h_val;
 
 // Enable CLK_H_MEM
 clk_out_enb_h_val = *(u32 *)CLK_OUT_ENB_SET_H;
 clk_out_enb_h_val &= ~(0x01);
 clk_out_enb_h_val |= 0x01;
 *(u32 *)CLK_OUT_ENB_SET_H = clk_out_enb_h_val;
 
 // Enable CLK_X_EMC_DLL
 u32 clk_out_enb_x_val = *(u32 *)CLK_OUT_ENB_SET_X;
 clk_out_enb_x_val &= ~(0x4000);
 clk_out_enb_x_val |= 0x4000;
 *(u32 *)CLK_OUT_ENB_SET_X = clk_out_enb_x_val;
 
 // Enable RST_H_EMC and RST_H_MEM
 *(u32 *)RST_DEVICES_SET_H = 0x2000001;
 
 // Wait a while
 mdelay(0x05);
 
 // Disable RST_Y_QSPI
 u32 rst_clr_y_val = *(u32 *)RST_DEVICES_CLR_Y;
 rst_clr_y_val &= ~(0x80000);
 rst_clr_y_val |= 0x80000;
 *(u32 *)RST_DEVICES_CLR_Y = rst_clr_y_val;
 
 // Refresh MC_IRAM_REG_CTRL
 // Should be set to 0 (MC_ENABLE_IRAM_CFG_WRITES)
 u32 mc_iram_reg_ctrl_val = *(u32 *)MC_IRAM_REG_CTRL;
 *(u32 *)MC_IRAM_REG_CTRL = mc_iram_reg_ctrl_val;
 
 // Set base and top addresses for AHB redirected IRAM path
 // This allows devices like the GPU to access this range
 *(u32 *)MC_IRAM_BOM = 0x40000000;
 *(u32 *)MC_IRAM_TOM = 0x4003F000;
 
 // Read back MC_IRAM_REG_CTRL
 mc_iram_reg_ctrl_val = *(u32 *)MC_IRAM_REG_CTRL;
 	
 return mc_iram_reg_ctrl_val;

Key generation

After the security engine is ready and before decrypting the next stage, the bootloader initializes and generates several keys into hardware keyslots. For more details on the Switch's cryptosystem, please see this page.

Selection

Depending on FUSE_RESERVED_ODM4 and FUSE_SPARE_BIT_5 different static seeds are selected for key generation.

 // Initialize keyslots 0x0C and 0x0D as readable
 init_keyslot(0x0C, 0x15);
 init_keyslot(0x0D, 0x15);
 
 // Find the BCT's data address from IRAM header
 u32 bct_data_addr = *(u32 *)bct_imem_addr + 0x4C;
 u32 bct_customer_data_addr = *(u32 *)bct_data_addr + 0x450;
 
 // Wrapper to get unit type from FUSE_RESERVED_ODM4
 // This tells if the device is retail or debug
 bool is_retail = is_unit_retail();
 
 u32 master_static_seed_addr = 0;
 u32 master_static_seed_size = 0;
 
 if (is_retail)
 {
    // Read FUSE_SPARE_BIT_5
    // This tells which master key to use
    u32 master_key_ver = read_fuse_spare_bit_5();
 
    // Invalid for retail
    if (!master_key_ver)
       panic();
    else
    {
       master_static_seed_addr = static_seed1_addr;
       master_static_seed_size = 0x10;
 
       // Generate retail keys
       generate_retail_keys(bct_customer_data_addr, static_seed_addr, static_seed_size);
    }
 }
 else
 {
    // Read FUSE_SPARE_BIT_5
    // This tells which master key to use
    u32 master_key_ver = read_fuse_spare_bit_5();
 
    // Use debug key set
    if (!master_key_ver)
    {
       // Read the first byte of the BCT RSA PSS signature
       u8 rsa_pss_1_byte = *(u8 *)bct_data_addr + 0x210;
 
       if (rsa_pss_1_byte == 0x11)
       {
          master_static_seed_addr = static_seed6_addr;
          master_static_seed_size = 0x10;
       }
       else	                          
       {
          master_static_seed_addr = static_seed7_addr;
          master_static_seed_size = 0x10;
       }
 
       // Generate debug keys
       generate_debug_keys(static_seed_addr, static_seed_size);
    }
    else
    {
       // Read the first byte of the BCT RSA PSS signature
       u8 rsa_pss_1_byte = *(u8 *)bct_data_addr + 0x210;
 
       if (rsa_pss_1_byte == 0x4F)		// Different key as in retail mode
       {
          master_static_seed_addr = static_seed0_addr;
          master_static_seed_size = 0x10;
       }
       else	                                // Same key as in retail mode
       {
          master_static_seed_addr = static_seed1_addr;
          master_static_seed_size = 0x10;
       }
 
       // Generate retail keys
       generate_retail_keys(bct_customer_data_addr, master_static_seed_addr, master_static_seed_size);
    }
 }
 
 // Initialize keyslots 0x0C and 0x0D as unreadable
 init_keyslot(0x0C, 0xFF);
 init_keyslot(0x0D, 0xFF);
 
 return;

generate_retail_keys

In order to generate retail keys, the bootloader starts by initializing TSEC and grabbing it's device key. Using static seeds and the SBK, the keyblob injected into the BCT's customer_data is validated and decrypted. The resulting keys will then be used to generate the master static key and the master device key.

See the pseudocode bellow for the detailed process.

 u32 in_addr = 0;
 u32 in_size = 0;
 u32 out_addr = 0;
 u32 out_size = 0;
 u32 keyslot = 0;
 u32 keyslot_dst = 0;
 
 // Get the TSEC device key
 tsec_get_device_key(tsec_device_key_addr, 0x10);
 
 // Install the TSEC device key into keyslot 0x0D
 set_keyslot_data(0x0D, tsec_device_key_addr, 0x10);
 
 in_addr = static_seed2_addr;
 in_size = 0x10;
 out_addr = keyblob_device_key_addr;
 out_size = 0x10;
 keyslot = 0x0D;
 
 // Use the tsec_device_key (keyslot 0x0D) to decrypt the static_seed2
 // This generates the keyblob_device_key
 aes_ecb_decrypt(out_addr, out_size, keyslot, in_addr, in_size);
 
 in_addr = keyblob_device_key_addr;
 in_size = 0x10;
 keyslot = 0x0E;
 keyslot_dst = 0x0D;
 
 // Use SBK (keyslot 0x0E) to further decrypt the
 // keyblob_device_key and install it into keyslot 0x0D
 // This will generate the keyblob_key
 decrypt_keyslot(keyslot_dst, keyslot, in_addr, in_size);
 
 // Clear SBK and SSK keyslots
 clear_keyslot(0x0E);
 clear_keyslot(0x0F);
 
 in_addr = static_seed4_addr;
 in_size = 0x10;
 keyslot = 0x0D;
 keyslot_dst = 0x0B;
 
 // Use keyblob_key (keyslot 0x0D) to decrypt the
 // static_seed4_addr and install it to keyslot 0x0B
 // This will generate the bct_mac_key
 decrypt_keyslot(keyslot_dst, keyslot, in_addr, in_size);
 
 in_addr = bct_customer_data_addr + 0x10;
 in_size = 0xA0;
 out_addr = mac_addr;
 out_size = 0x10;
 keyslot = 0x0B;
 
 // Use the bct_mac_key (keyslot 0x0B) to generate
 // CMAC over bct_customer_data_addr + 0x10
 aes_cmac(out_addr, out_size, keyslot, in_addr, in_size);
 
 // Comapre the generated hash with the first
 // 0x10 bytes of bct_customer_data
 bool match = safe_memcmp(mac_addr, bct_customer_data_addr, 0x10);
 
 // Hashes don't match
 if (!match)
    panic();
 
 in_addr = bct_customer_data_addr + 0x20;
 in_size = 0x90;
 ctr_addr = bct_customer_data_addr + 0x10;
 ctr_size = 0x10;
 out_addr = dec_payload_addr;
 out_size = 0x90;
 keyslot = 0x0D;
 
 // AES-CTR decrypt
 // Use the keyblob_key (keyslot 0x0D) to decrypt bct_customer_data_addr + 0x20
 // using bct_customer_data_addr + 0x10 as CTR
 aes_ctr_decrypt(out_addr, out_size, keyslot, in_addr, in_size, ctr_addr, ctr_size);
 
 // Install the last decrypted keyblob key into keyslot 0x0B
 // This is the pk11_key
 set_keyslot_data(0x0B, dec_payload_addr + 0x80, 0x10);
 
 // Install the first decrypted keyblob key into keyslot 0x0C
 // This is the master_static_kek
 set_keyslot_data(0x0C, dec_payload_addr, 0x10);
 
 // Clear out the decrypted data
 memclear(dec_payload_addr, 0x90);
 
 in_addr = master_static_seed_addr;
 in_size = master_static_seed_size;
 keyslot = 0x0C;
 keyslot_dst = 0x0C;
 
 // Use the master_static_kek (keyslot 0x0C) to decrypt
 // master_static_seed and install it into keyslot 0x0C
 // This will generate the master_static_key
 decrypt_keyslot(keyslot_dst, keyslot, in_addr, in_size);
 
 in_addr = static_seed3_addr;
 in_size = 0x10;
 keyslot = 0x0D;
 keyslot_dst = 0x0D;
 
 // Use keyblob_key (keyslot 0x0D) to decrypt
 // static_seed3_addr and install it into keyslot 0x0D
 // This will generate the master_device_key
 decrypt_keyslot(keyslot_dst, keyslot, in_addr, in_size);
 
 return;

generate_debug_keys

In order to generate debug keys, the bootloader only uses static seeds, the SBK and the SSK.

See the pseudocode bellow for the detailed process.

 u32 in_addr = 0;
 u32 in_size = 0;
 u32 keyslot = 0;
 u32 keyslot_dst = 0;
 
 in_addr = static_seed8_addr;
 in_size = 0x10;
 keyslot = 0x0E;
 keyslot_dst = 0x0B;
 
 // Use SBK (keyslot 0x0E) to decrypt the
 // static_seed8 and install it to keyslot 0x0B
 // This will generate debug_pk11_key
 decrypt_keyslot(keyslot_dst, keyslot, in_addr, in_size);
 
 in_addr = static_seed5_addr;
 in_size = 0x10;
 keyslot = 0x0E;
 keyslot_dst = 0x0C;
 
 // Use SBK (keyslot 0x0E) to decrypt the
 // static_seed5 and install it to keyslot 0x0C
 // This will generate debug_master_static_kek
 decrypt_keyslot(keyslot_dst, keyslot, in_addr, in_size);
 
 in_addr = static_seed9_addr;
 in_size = 0x10;
 keyslot = 0x0F;
 keyslot_dst = 0x0D;
 
 // Use SSK (keyslot 0x0F) to decrypt the
 // static_seed9 and install it to keyslot 0x0D
 // This will generate debug_keyblob_key
 decrypt_keyslot(keyslot_dst, keyslot, in_addr, in_size);
 
 // Clear SBK and SSK keyslots
 clear_keyslot(0x0E);
 clear_keyslot(0x0F);
 
 in_addr = master_static_seed_addr;
 in_size = master_static_seed_size;
 keyslot = 0x0C;
 keyslot_dst = 0x0C;
 
 // Use the debug_master_static_kek (keyslot 0x0C) to decrypt the
 // master_static_seed and install it to keyslot 0x0C
 // This will generate the master_static_key
 decrypt_keyslot(keyslot_dst, keyslot, in_addr, in_size);
 
 in_addr = static_seed3_addr;
 in_size = 0x10;
 keyslot = 0x0D;
 keyslot_dst = 0x0D;
 
 // Use debug_keyblob_key (keyslot 0x0D) to decrypt the
 // static_seed3 and install it to keyslot 0x0D
 // This will generate the master_device_key
 decrypt_keyslot(keyslot_dst, keyslot, in_addr, in_size);
 
 return;

Package1 (PK11)

This blob is stored encrypted inside the package and is decrypted by package1ldr.

Encryption

The encrypted blob is prepended with it's CTR and total image size. After checking the image's size against an hardcoded value (can change on firmware updates), the image is AES-CTR decrypted and the keyslot used for decryption is immediately cleared.

 // Maximum encrypted blob's size on firmware version 1.0.0
 u32 max_pk11_enc_blob_size = 0x29000;
 
 u32 pk11_enc_blob_size = *(u32 *)pk11_blob_addr;
 u32 pk11_enc_blob_ctr_addr = pk11_blob_addr + 0x10; 
 u32 pk11_enc_blob_addr = pk11_blob_addr + 0x20;
 
 // Validate the encrypted blob's size
 if (pk11_enc_blob_size > max_pk11_enc_blob_size)
    panic();
 
 u32 in_addr = pk11_enc_blob_addr;
 u32 in_size = pk11_enc_blob_size;
 u32 ctr_addr = pk11_enc_blob_ctr_addr;
 u32 ctr_size = 0x10;
 u32 out_addr = pk11_dec_blob_addr;
 u32 out_size = pk11_dec_blob_size;
 u32 keyslot = 0x0B;
 
 // AES-CTR decrypt
 // Use the pk11_key (keyslot 0x0B) to decrypt the blob in place
 aes_ctr_decrypt(out_addr, out_size, keyslot, in_addr, in_size, ctr_addr, ctr_size);
 
 // Clear pk11_key keyslot
 clear_keyslot(0x0B);
 
 // Validate the decrypted blob
 // Checks the "PK11" magic and some pk11 header fields
 bool is_valid = check_pk11_header(pk11_dec_blob_addr, pk11_dec_blob_size);
 
 // Invalid PK11 image
 if (!is_valid)
    panic();
 
 u32 pk11_header_size = 0x20;
 u32 pk11_sec1_offset = *(u32 *)pk11_dec_blob_addr + 0x14;
 u32 pk11_sec2_size = *(u32 *)pk11_dec_blob_addr + 0x18;
 
 // Calculate NX bootloader's entrypoint
 u32 nx_boot_addr = (pk11_dec_blob_addr + pk11_header_size + pk11_sec1_offset + pk11_sec2_size);
 		
 return nx_boot_addr;

Header

When decrypted, the blob is encapsulated in the following header.

Offset	Size	Description
0x0	4	Magic "PK11"
0x4	4	Section 0 size
0x8	4	Section 0 offset
0xC	4	Unknown
0x10	4	Section 1 size
0x14	4	Section 1 offset
0x18	4	Section 2 size
0x1C	4	Section 2 offset

What each section is used for may vary per system-version.

Section 0

This section contains the warmboot binary.

Section 1

This section contains the NX bootloader, which is run after the initial bootloader in package1.

Section 2

This section contains the Secure Monitor binary.

Changelog

2.0.0

• The encrypted binaries' order and calculation for next stage's entrypoint was changed.

Old layout (before 2.0.0):

1.- PK11 header
2.- Secure Monitor blob
3.- NX bootloader blob
4.- Warmboot blob

NX bootloader entrypoint is calculated as:
0x40013FE0 + 0x20 + 0x20 + NX bootloader blob's offset + Secure Monitor blob's size

New layout (2.0.0+):

1.- PK11 header
2.- Warmboot blob
3.- NX bootloader blob
4.- Secure Monitor blob

NX bootloader entrypoint is calculated as:
0x40013FE0 + 0x20 + 0x20 + NX bootloader blob's offset + Warmboot blob's size

• Some AES-ECB decryption related code was refactored.

3.0.0

• The functions set_se_addr() and check_se_status() are now called right after enabling the security engine clocks and resets.

See Switch_System_Flaws#Stage_1_Bootloader.

• Keyslot 0x0A is now used instead of keyslot 0x0D for generating the master_device_key.