LDN services: Difference between revisions

Line 1,096:

Then the Station scans for an [[#ActionFrame]] for loading the [[#NetworkInfo]].

Once connected, the Station must Authenticate with the AccessPoint, this is custom. The Station sends a frame (a maximum of 3 times in some cases if errors occur, with the same data), and the AccessPoint sends a response. Once Authenticated, the node is added to the [[#NodeInfo]] array in [[#NetworkInfo]]. If the Station does not successfully Authenticate X-seconds after connecting, the AccessPoint disconnects the Station. If the Station fails to Authenticate, the Station itself will disconnect as well.

Once connected, the AccessPoint sends Epigram-vendor Action frame(s) (same data) to the Station, the Station doesn't require these frames: <code>dd1afeedfacedeadbeef010000000a00000000000000000000000000</code>. Then the Station must Authenticate with the AccessPoint, this is custom. The Station sends a frame (a maximum of 3 times in some cases if errors occur, with the same data), and the AccessPoint sends a response. Once Authenticated, the node is added to the [[#NodeInfo]] array in [[#NetworkInfo]]. If the Station does not successfully Authenticate X-seconds after connecting, the AccessPoint disconnects the Station. If the Station fails to Authenticate, the Station itself will disconnect as well.

After Authentication the Station will scan for another [[#ActionFrame]], with frame-comparision enabled with the above frame (frame must have been updated since the previous scan). The Station locates the index for a [[#MacAddress]] matching itself in the [[#NetworkInfo]] [[#NodeInfo]] array (the entry for the AccessPoint is skipped), throwing an error if not found. After validating the LocalCommunicationVersion, it proceeds to handle ARP setup below.

Line 1,114:

*** 0x0103: ?

* The first byte of Data is value 0, then the ProtocolID-specific data follows, see below.

** ProtocolID 0x0103 frames are sent by the AccessPoint to the Station. This is 0x20-bytes of zeros, except for the first byte which is 0x3. This is sent by the AccessPoint prior to destroying the network?

** ProtocolID 0x0103 frames are sent by the AccessPoint to the Station. This is 0x20-bytes of zeros, except for the first byte which is 0x3. This is sent by the AccessPoint prior to destroying the network.

==== Authentication ====

@@ Line 1,096: / Line 1,096: @@
 Then the Station scans for an [[#ActionFrame]] for loading the [[#NetworkInfo]].
-Once connected, the Station must Authenticate with the AccessPoint, this is custom. The Station sends a frame (a maximum of 3 times in some cases if errors occur, with the same data), and the AccessPoint sends a response. Once Authenticated, the node is added to the [[#NodeInfo]] array in [[#NetworkInfo]]. If the Station does not successfully Authenticate X-seconds after connecting, the AccessPoint disconnects the Station. If the Station fails to Authenticate, the Station itself will disconnect as well.
+Once connected, the AccessPoint sends Epigram-vendor Action frame(s) (same data) to the Station, the Station doesn't require these frames: <code>dd1afeedfacedeadbeef010000000a00000000000000000000000000</code>. Then the Station must Authenticate with the AccessPoint, this is custom. The Station sends a frame (a maximum of 3 times in some cases if errors occur, with the same data), and the AccessPoint sends a response. Once Authenticated, the node is added to the [[#NodeInfo]] array in [[#NetworkInfo]]. If the Station does not successfully Authenticate X-seconds after connecting, the AccessPoint disconnects the Station. If the Station fails to Authenticate, the Station itself will disconnect as well.
 After Authentication the Station will scan for another [[#ActionFrame]], with frame-comparision enabled with the above frame (frame must have been updated since the previous scan). The Station locates the index for a [[#MacAddress]] matching itself in the [[#NetworkInfo]] [[#NodeInfo]] array (the entry for the AccessPoint is skipped), throwing an error if not found. After validating the LocalCommunicationVersion, it proceeds to handle ARP setup below.
@@ Line 1,114: / Line 1,114: @@
 *** 0x0103: ?
 * The first byte of Data is value 0, then the ProtocolID-specific data follows, see below.
-** ProtocolID 0x0103 frames are sent by the AccessPoint to the Station. This is 0x20-bytes of zeros, except for the first byte which is 0x3. This is sent by the AccessPoint prior to destroying the network?
+** ProtocolID 0x0103 frames are sent by the AccessPoint to the Station. This is 0x20-bytes of zeros, except for the first byte which is 0x3. This is sent by the AccessPoint prior to destroying the network.
 ==== Authentication ====