Gamecard

For the Gamecard partitions that can be mounted, see here.

For the format of the Gamecard image, see here.

Gamecard controller

The gamecard controller (known internally as the LOTUS3) is a separate chip on the motherboard responsible for communicating with the gamecard.

FS flashes the appropriate gamecard controller's firmware (Lotus ASIC Firmware or LAFW) which is encrypted, signed and follows the format below.

Offset	Size	Description
0x0	0x100	RSA-PKCS#1 signature
0x100	0x4	Magic ("LAFW")
0x104	0x4	Unknown (0xFF000000, 0xFFFF0000 or 0xFFFFFF00)
0x108	0x4
0x10C	0x4
0x110	0x4	Version (0, 1 or 3)
0x114	0x4	Unknown (0x80000000)
0x118	0x4	Data size
0x11C	0x4
0x120	0x10	Data hash
0x130	0x10	Placeholder string ("IDIDIDIDIDIDIDID")
0x140	0x40	Empty
0x180	0x7680	Encrypted data

Hardware

A Switch game cartridge, frontside	A Switch game cartridge, backside
Close-up of frontside PCB	Close-up of backside PCB
Close-up of stripped frontside PCB

Pinout

Pin	Name	Direction	Description
0	IRQ?	Output	Always wired to GND inside game cartridge; Possibly used for interrupt signaling
1	RCLK	Output	Return clock; Game cartridge sends back CLK signal delayed by a few ns
2	CLK	Input	Clock, 25MHz
3	CS	Input	Chip select; Switch pulls this LOW during a transfer
4	DAT0	Inout	Data bus pin 0
5	DAT1	Inout	Data bus pin 1
6	VCC 3.3v	Input
7	DAT2	Inout	Data bus pin 2
8	DAT3	Inout	Data bus pin 3
9	VCC 1.8v	Input
10	DAT4	Inout	Data bus pin 4
11	DAT5	Inout	Data bus pin 5
12	DAT6	Inout	Data bus pin 6
13	DAT7	Inout	Data bus pin 7
14	GND
15	RST	Input	Reset, active LOW.

All IO use 1.8V for logic HIGH and 0V for logic LOW.

Protocol

Switch game cartridges use a simple (but Nintendo proprietery) SPI-like bus with 8-bit width (DAT7..0). It is very similar to the bus interface of 3DS game cartridges, except with very different commands.

The Switch host starts a transfer by first pulling CS low, followed by clocking a byte each clock cycle. The bus data will always be ready before the rising edge of the CLK signal, so that it can be captured on the rising edge. After command bytes are written to the bus, the direction of the bus implicitly changes and the game cartridge responds. The Switch host keeps clocking while the game cartridge responds. After the transfer is ended, the CS line is pulled high again.

Commands are 16 bytes long, and followed immediately by a 4-byte CRC-32 over the command bytes. After this, the Switch stops driving the data bus, and the bus will be 'floating'. Due to the pull-ups on the bus, it will slowly converge to logic HIGH state. The Switch will clock 2 cycles to allow the bus to settle a direction change. The Switch host will then clock another cycle and if the game cartridge didn't receive the CRC OK, it will respond with "01". Otherwise it will respond with "00" and pull DAT0 low on the next cycle to signal it is busy. The Switch host will then keep clocking until the cartridge is ready.

When the game cartridge is ready to send the actual data response, it will pull the DAT0 pin high for 2 cycles to let the Switch host know. After this, the game cartridge will send the actual data response bytes.

The actual response bytes are also followed immediately by a 4-byte CRC-32 over the actual data response bytes.

Commands

A typical boot up sequence of a game cartridge (in this case, the game "1,2 Switch") looks like this:

Command	Size	Description
5B000000000000010000000000000000	0x200	Read sector 0, contains "HEAD" blob
5B000000000000010000000000000000	0x200	Read sector 0, contains "HEAD" blob
56000000000000000000000000000000	0x4	Read card id "AE F8 01 21"
28000000000000000000000000000000	0x4	Read ??? "02 00 00 00"
A5000000000000000000000000000000	0x4	Read ??? "00 00 00 00"
56000000000000000000000000000000	0x4	Read card id "AE F8 01 21"
28000000000000000000000000000000	0x4	Read ??? "02 00 00 00"
5B000000380000010000000000000000	0x200	Read sector 0x38, contains "CERT" blob
E2000000000000000000000000000000	0x4	Read ??? "01 00 00 00"
E0000000000000000000000000000000	0x200	Read crypto-challenge header
200838A25A344F818ABB6456694D4E8D	0	Enter crypto mode1 with HOST-RANDOM "0838A25A344F818ABB6456694D4E8D"
7EE41FDF12C01C157CC899910673A0CF	0x40	Encrypted crypto mode1 command, reads CART-RANDOM
263C8230EC15FAE3CE79365BD850F4BD	0x0	Encrypted mode1 command, enters crypto mode2 with (HOST-RANDOM, CART-RANDOM)
B6FDA6F37FFA29E18831D0B217DFBDBE	0x4	Encrypted mode2 command, possibly read card id?
7B97F7DF07240AA9870E1C974336FA8A	0x4	Encrypted mode2 command

The meaning of some these commands are currently unknown.

Observations

• The "update" and "normal" partitions can be dumped using the plaintext 5B commands
• The "secure" partition can only be read from encrypted mode.

Encryption

After a few initial plaintext commands, the Switch instructs the game cartridge to enter into encrypted mode. From that point on, commands and responses are sent encrypted over the bus. The encryption algorithm used is currently unknown.

There appear to be 2 kinds of crypto mode.

Crypto mode1 is initiated solely by the HOST-RANDOM as random session seed. In that mode, the Switch host requests for the game cartridge random seed, and then sends a command to enter crypto mode2.

Crypto mode2 takes into account the CART-RANDOM seed generated by the cartridge, and possibly the previous HOST-RANDOM. The game cartridge will always send a different CART-RANDOM even if the exact same command sequence is replayed and thus with this scheme replay attacks are not possible.

Manufacturers

Macronix (MX)

Uses package: LGA

Uses card id: 0xC2

OKI Semiconductor

Uses package: TSOP-48

Uses card id: 0xAE

SanDisk?

Uses package: ??

Uses card id: 0x45 ?