Nintendo Switch Brew

Changes

HIPC (view source)

Revision as of 18:36, 29 November 2023

10,427 bytes added ,  18:36, 29 November 2023
no edit summary
Line 1: Line 1: −
== IPC Command Structure ==
+
HIPC (Horizon Inter-Process Communication) is a custom IPC implementation tailored for the Horizon OS.
−
This is an array of u32's, usually located in [[Thread Local Storage]].
+
 
 +
= Structure =
 +
This is a buffer located in the [[Thread Local Region]].
    
{| class="wikitable" border="1"
 
{| class="wikitable" border="1"
−
! Word || Bits || Description
   
|-
 
|-
−
| 0 || 15-0 || Type. 4=Request, 5=Control
+
! Offset || Size || Description
 
|-
 
|-
−
| 0 || 19-16 || Number of buf X descriptors (each: 2 words).
+
| 0x0 || 0x8 || [[#HeaderData|HeaderData]]
 
|-
 
|-
−
| 0 || 23-20 || Number of buf A descriptors (each: 3 words).
+
| 0x8 || Variable || [[#SpecialData|SpecialData]] (if HasSpecial is set)
 
|-
 
|-
−
| 0 || 27-24 || Number of buf B descriptors (each: 3 words).
+
| Variable || Variable || Array of [[#PointerData|PointerData]]
 
|-
 
|-
−
| 0 || 31-28 || Number of buf W desciptors (each: 3 words), never observed.
+
| Variable || Variable || Array of [[#MapData|SendData]]
 
|-
 
|-
−
| 1 || 9-0 || Size of raw data section in u32s.
+
| Variable || Variable || Array of [[#MapData|ReceiveData]]
 
|-
 
|-
−
| 1 || 13-10 || Flags for buf C descriptor.
+
| Variable || Variable || Array of [[#MapData|ExchangeData]]
 
|-
 
|-
−
| 1 || 30-20 || ?
+
| Variable || Variable || [[#RawData|RawData]]
 +
|-
 +
| Variable || Variable || Array of [[#ReceiveListData|ReceiveListData]]
 +
|}
 +
 
 +
[[#HeaderData|HeaderData]] and [[#SpecialTag|SpecialHeaderData]] (if available) are copied as-is from one process to another.
 +
 
 +
Sysmodules load the last u64 of rawdata when handling the [[#SpecialData|SpecialData]] ProcessId. This is not written by kernel. For sysmodule handling:
 +
* In some cases: these commands require a placeholder u64 value passed in the input parameters, as mentioned above. In these cases the OverwriteClientProcessId method is called to replace the value before it is used.
 +
* In other cases: The rawdata_u64 is compared with the ProcessId from [[#SpecialData|SpecialData]]. On mismatch and when rawdata_u64!=0, error 0x60A is returned. The ProcessId value passed to the cmdhandler vtable funcptr is the rawdata_u64.
 +
 
 +
Handle 0 is allowed, and just means no handle was sent.
 +
 
 +
A reply must not use Send/Receive/Exchange data buffers, svcReplyAndReceive will return 0xE801. [[SVC|MemoryAttribute]] IsBorrowed and IsUncached are never allowed for the source address. "Send" means buffer is sent from source process into service process, "Receive" means that data is copied from service process into user process and "Exchange" means both "Send" and "Receive".
 +
 
 +
[[#HeaderData|HeaderData]]'s ReceiveListCount field controls the behavior of [[#ReceiveListData|ReceiveListData]].
 +
 
 +
If ReceiveListCount is 0, [[#ReceiveListData|ReceiveListData]] is disabled. If ReceiveListCount is 1, there is an "inlined" [[#ReceiveListData|ReceiveListData]] buffer after the raw data (received data is copied to ROUND_UP(cmdbuf+raw_size+index, 16)). If ReceiveListCount is 2, there is a single [[#ReceiveListData|ReceiveListData]] buffer. Otherwise it has (ReceiveListCount-2) [[#ReceiveListData|ReceiveListData]] buffers. In this case, ReceiveIndex picks which [[#ReceiveListData|ReceiveListData]] buffer to copy received data to [instead of picking the offset into the buffer]. Data sent with this method must have MemoryState 0x4000000 mask set.
 +
 
 +
After reply, [[#PointerData|PointerData]] buffers are written to the sender containing the AddressValue, Size and ReceiveIndex that were copied to.
 +
 
 +
== RawData ==
 +
[[File:Ipc msg buffer type a example.png|thumb|An example of an IPC message with a type 0xA (OutPointer) buffer in it. Red is headers/descriptors, yellow is padding, and blue is data/buffer lengths. Note that the size of the u16 array for type 0xA lengths is padded to fill up a whole word.]]
 +
 
 +
{| class="wikitable" border="1"
 
|-
 
|-
−
| 1 || 31 || Enable handle descriptor.
+
! Offset || Size || Description
 
|-
 
|-
−
| ... || || [[#Handle descriptor|Handle descriptor]], if enabled.
+
| Variable || Variable || Reserved (padding to align to 16 bytes)
 
|-
 
|-
−
| ... || || [[#Buffer descriptor X "Pointer"|Buf X descriptors]], each one 2 words.
+
| Variable || Variable || [[#Payload|Payload]] or [[#Domain|Domain]]  
 
|-
 
|-
−
| ... || || [[#Buffer descriptor A/B/W "Send"/"Receive"/"Exchange"|Buf A descriptors]], each one 3 words.
+
| Variable || Variable || Reserved (padding to align to 16 bytes)
 
|-
 
|-
−
| ... || || [[#Buffer descriptor A/B/W "Send"/"Receive"/"Exchange"|Buf B descriptors]], each one 3 words.
+
| Variable || Variable || Buffer type 0xA (OutPointer) lengths (u16 array)
 +
|}
 +
 
 +
The total amount of padding within the raw data section is always 0x10 bytes. This means that if no padding is required before the message, there will be 0x10 bytes of padding after the message (before the buffer type 0xA (OutPointer) - lengths).
 +
 
 +
=== Payload ===
 +
This is an array of u32s, but individual parameters are generally stored as u64s.
 +
 
 +
{| class="wikitable" border="1"
 
|-
 
|-
−
| ... || || [[#Buffer descriptor A/B/W "Send"/"Receive"/"Exchange"|Type W descriptors]], each one 3 words.
+
! Offset || Size || Description
 
|-
 
|-
−
| ... || || [[#Raw_data_section|Raw data section]] (including padding before and after aligned data section).
+
| 0x0 || 0x10 || [[#CmifInHeader|CmifInHeader]] or [[#CmifOutHeader|CmifOutHeader]]
 
|-
 
|-
−
| ... || || [[#Buffer descriptor C "ReceiveList"|Buf C descriptors]], each one 2 words.
+
| 0x10 || Variable || Input parameters or return values
 
|}
 
|}
   −
First two header u32's and handle descriptor (if enabled) are copied as-is from one process to the other.
+
The rawdata struct for input parameters/return values is generated by stable-sorting function parameters by alignment, from low to high. It is likely this is a mistake, as it generates structs with suboptimal possible padding -- Nintendo probably meant to sort from high to low (which would give minimized padding), but couldn't/can't change this without breaking backwards compatibility.
   −
=== Handle descriptor ===
+
=== Domain ===
−
There can only be one of this descriptor type. It is enabled by bit31 of the second word.
+
Because the switch has relatively low limits on the total number of sessions available to the system (Kernel slabheap limits, sysmodule handle table size limits), HIPC supports a "Domains" feature that allows multiplexing multiple service sessions through a single handle. Domains store (effectively) a mapping from u32 object id to a SharedPointer<IServiceObject> -- When messages are sent to a domain, an extra header is sent in the raw data section (before anything else) with information about what object in the domain is being acted on; responses similarly contain an additional header. Official session code implements this by just using the dispatch table for the object in the map with the appropriate ID, instead of the dispatch table the session was initialized with.
    
{| class="wikitable" border="1"
 
{| class="wikitable" border="1"
−
! Word || Bits || Description
   
|-
 
|-
−
| 0 || 0 || Send current PID.
+
! Offset || Size || Description
 
|-
 
|-
−
| 0 || 4-1 || Number of handles to copy
+
| 0x0 || 0x10 || [[#CmifDomainMessageInHeader|CmifDomainMessageInHeader]] or [[#CmifDomainMessageOutHeader|CmifDomainMessageOutHeader]]
 
|-
 
|-
−
| 0 || 8-5 || Number of handles to move
+
| 0x10 || Variable || [[#Payload|Payload]] (size must be InRawSize, only for input domain messages)
 
|-
 
|-
−
| ... || || 8-byte PID if enabled
+
| Variable || Variable || Array of [[#CmifDomainObjectId|CmifDomainObjectId]] (count must be InObjectCount, only for input domain messages)
 +
|}
 +
 
 +
= Messages =
 +
IPC messages can have different types which influence how the IPC server processes requests. The message type value is passed in the lower 16 bits of the first [[#HeaderData|HeaderData]] word (see [[#Header0Tag|Header0Tag]]).
 +
 
 +
== InvokeMethod ==
 +
This is a normal message to be processed using the regular marshalling system. Now deprecated, this type of message would be copied first to an intermediary set of internal structures by the server.
 +
 
 +
== Release ==
 +
This is a message that tells to close and destroy the server session.
 +
 
 +
== InvokeManagerMethod ==
 +
This is a message that requests a server manager operation. Now deprecated, this type of message would be copied first to an intermediary set of internal structures by the server.
 +
 
 +
{| class="wikitable" border="1"
 
|-
 
|-
−
| ... || || Handles to copy
+
! Cmd || Name
 
|-
 
|-
−
| ... || || Handles to move
+
| 0 || [[#ConvertCurrentObjectToDomain]]
 +
|-
 +
| 1 || [[#CopyFromCurrentDomain]]
 +
|-
 +
| 2 || [[#CloneCurrentObject]]
 +
|-
 +
| 3 || [[#QueryPointerBufferSize]]
 +
|-
 +
| 4 || [[#CloneCurrentObjectEx]]
 
|}
 
|}
   −
Sysmodules load the last u64 of rawdata when handling the PID. This is not written by kernel. For sysmodule handling:
+
=== ConvertCurrentObjectToDomain ===
−
* In some cases: these commands require a placeholder u64 value passed in the input parameters, as mentioned above. In these cases the OverwriteClientProcessId method is called to replace the value before it is used.
+
No input. Returns an output [[#CmifDomainObjectId|CmifDomainObjectId]].
−
* In other cases: The rawdata_u64 is compared with the PID from the descriptor. On mismatch and when rawdata_u64!=0, error 0x60A is returned. The PID value passed to the cmdhandler vtable funcptr is the rawdata_u64.
+
 
 +
=== CopyFromCurrentDomain ===
 +
Takes an input [[#CmifDomainObjectId|CmifDomainObjectId]]. Returns an output handle.
 +
 
 +
=== CloneCurrentObject ===
 +
No input. Returns an output handle.
 +
 
 +
=== QueryPointerBufferSize ===
 +
No input. Returns an output u16 '''PointerBufferSize'''.
 +
 
 +
=== CloneCurrentObjectEx ===
 +
Takes an input u32 '''Tag'''. Returns an output handle.
 +
 
 +
== Invoke2Method ==
 +
Same as [[#InvokeMethod|InvokeMethod]] but using a more streamlined logic that no longer requires additional internal copying and parsing.
 +
 
 +
== Invoke2ManagerMethod ==
 +
Same as [[#InvokeManagerMethod|InvokeManagerMethod]] but using a more streamlined logic that no longer requires additional internal copying and parsing.
 +
 
 +
== Invoke2MethodWithContext ==
 +
Same as [[#Invoke2Method|Invoke2Method]] but with the additional requirement of suppling a token in the [[#Data payload|data payload]].
 +
 
 +
This token is used by "nn::sf::cmif::SetInlineContext" which has the sole purpose of saving it into the TLS in order for it to be distributed to any IPC commands that are made while processing the current command. It's unknown if this token serves any purpose or if it's just a debug-tool to figure out what IPC command caused a particular chain of commands.
 +
 
 +
== Invoke2ManagerMethodWithContext ==
 +
Same as [[#Invoke2ManagerMethod|Invoke2ManagerMethod]] but with the additional requirement of suppling a token in the [[#Data payload|data payload]].
 +
 
 +
This token is used by "nn::sf::cmif::SetInlineContext" which has the sole purpose of saving it into the TLS in order for it to be distributed to any IPC commands that are made while processing the current command. It's unknown if this token serves any purpose or if it's just a debug-tool to figure out what IPC command caused a particular chain of commands.
 +
 
 +
= Server =
 +
Send/Receive/Exchange data buffers map memory into the sysmodule process. For the mapped memory in the sysmodule the permissions are: Send = R--, Receive = RW-. The buffer is automatically unmapped while the kernel handles the cmdreply, the sysmodule doesn't need to specify anything in the cmdreply to trigger this.
 +
 
 +
This memory is mapped in the sysmodule to the same vaddr from the original user-process cmd-request, except with with bits >=(~28(?)) changed to a different ASLR'd region.
 +
 
 +
No user-process->sysmodule memcpy is done for outbufs, only sysmodule->user-process.
 +
 
 +
ReceiveList/Pointer data buffers are somewhat different. Rather than mapping new memory into the server process, ReceiveList/Pointer data buffers copy data between existing buffers in different processes. Each Pointer data buffer in a message has its data copied into a ReceiveList data buffer on the other side. Each Pointer data buffer in a message is used to reserve space for the other side's ReceiveList data buffer to copy into.
 +
 
 +
When the kernel processes Pointer data buffers, it must determine where to copy the data to. If the destination used ReceiveList data buffers with flags >= 3, each Pointer data buffer from the source is matched to a ReceiveList data buffer in the destination by the Pointer data buffer's ReceiveIndex field. If the destination used a single ReceiveList data buffer, the data from all the Pointer data buffers is copied into the same buffer specified by the destination's ReceiveList data buffer (causing error 0xce01 if there is not enough space) and the Pointer data buffer's ReceiveIndex is ignored. The kernel then modifies the addresses in the Pointer data buffers to indicate where the data was copied to in the destination.
 +
 
 +
Before receiving a request, if the IPC server is expecting Pointer data buffers, it prepares a message with a single ReceiveList data buffer (flags=2) in its message buffer before calling svcReplyAndReceive so that Pointer data buffers from the client have a place to copy their data to. The usage of the flag-2 ReceiveList data buffer allows the server to receive an arbitrary number of Pointer data buffers, since they're all packed into the same buffer. If the server had used flag-3+ ReceiveList data buffers, it would be limited in how many Pointer data buffers it could receive since the Pointer data buffers would have to be matched to distinct ReceiveList data buffers. The buffer that the server's ReceiveList data buffer points to is called the '''pointer buffer'''.
 +
 
 +
When the client sends Pointer data buffers, data is copied into the server's pointer buffer. When the client sends ReceiveList data buffers, no data is copied automatically. The server needs to use Pointer data buffers to copy the data back to the client's ReceiveList data buffers (using the index field to match Pointer data buffers in the response back to the correct ReceiveList data buffers).
 +
 
 +
= Client =
 +
The official marshalling function for the client is called "nn::sf::hipc::client::Hipc2ClientCoreProcessorImpl::WriteBufferDataImpl" and takes:
 +
* A pointer to a "nn::sf::hipc::detail::HipcMessageWriter" context;
 +
* The number of (buf_ptr, size) pairs;
 +
* An array of (buf_ptr, size) pairs (called "nn::sf::detail::PointerAndSize");
 +
* A pointer to a type bitfield for each such pair;
 +
* The offset of the main IPC command structure;
 +
* The size of the IPC command's raw data payload.
   −
Handle 0 is allowed, and just means no handle was sent.
+
Pointer and ReceiveList data buffers are backed by the "pointer buffer", a buffer in the service process. Its size is a u16, which is retrieved using the "QueryPointerBufferSize" control message. If the client code determines all buffers with [[#BufferAttribute|BufferAttribute]] HipcPointer do not fit in the pointer buffer, it returns error 0x11A0B.
   −
=== Buffer descriptor X "Pointer" ===
+
For buffers with [[#BufferAttribute|BufferAttribute]] HipcAutoSelect, it creates two data buffers (Send+Pointer or Receive+ReceiveList), but one of them is NULL (zero size and pointer), while the other holds the expected values. Pointer/ReceiveList data buffers are used as the non-NULL buffer where possible, but if they don't fit in the pointer buffer, Send/Receive descriptors are used instead. The code defers processing of HipcAutoSelect buffers with sizes that fit in a u16 (and may therefore fit in the pointer buffer), which ensures all HipcPointer buffers get pointer-buffer space before any HipcAutoSelect. The order in which the deferred HipcAutoSelect buffers are processed is determined by a convoluted loop.
−
This one is packed even worse than A, they inserted the bit38-36 of the address ''on top'' of the counter field.
     −
Officially, the counter is known as "receive index". This one writes to the buffer described in the ReceiveList.
+
= HipcMessageDataInfo =
 +
This is "nn::sf::hipc::detail::HipcMessageDataInfo". This is a 0x38-byte struct.
    
{| class="wikitable" border="1"
 
{| class="wikitable" border="1"
−
! Word || Bits || Description
   
|-
 
|-
−
| 0 || 5-0 || Bits 5-0 of counter.
+
! Offset || Size || Description
 +
|-
 +
| 0x0 || 0x1 || Valid
 
|-
 
|-
−
| 0 || 8-6 || Bit 38-36 of address.
+
| 0x1 || 0x1 || HasSpecial
 
|-
 
|-
−
| 0 || 11-9 || Bits 11-9 of counter.
+
| 0x2 || 0x2 || Reserved
 
|-
 
|-
−
| 0 || 15-12 || Bit 35-32 of address.
+
| 0x4 || 0x8 || [[#HeaderData|HeaderData]]
 
|-
 
|-
−
| 0 || 31-16 || Size
+
| 0xC || 0x4 || [[#SpecialTag|SpecialHeaderData]]
 
|-
 
|-
−
| 1 || || Lower 32-bits of address.
+
| 0x10 || 0x4 || [[#HipcMessageDataOffsetInfo|DataOffsetInfo]]
 
|}
 
|}
   −
=== Buffer descriptor A/B/W "Send"/"Receive"/"Exchange" ===
+
= HeaderData =
−
This packing is so unnecessarily complex.
+
This is "nn::sf::hipc::detail::HipcFormat::HeaderData". This is a 0x8-byte struct.
    
{| class="wikitable" border="1"
 
{| class="wikitable" border="1"
−
! Word || Bits || Description
   
|-
 
|-
−
| 0 || || Lower 32-bits of size.
+
! Offset || Size || Description
 +
|-
 +
| 0x0 || 0x4 || [[#Header0Tag|Header0]]
 
|-
 
|-
−
| 1 || || Lower 32-bits of address.
+
| 0x4 || 0x4 || [[#Header1Tag|Header1]]
 +
|}
 +
 
 +
= MapData =
 +
This is "nn::sf::hipc::detail::HipcFormat::MapData". This is a 0xC-byte struct.
 +
 
 +
{| class="wikitable" border="1"
 
|-
 
|-
−
| 2 || 1-0 || Flags. Always set to 0, 1 or 3.
+
! Offset || Size || Description
 
|-
 
|-
−
| 2 || 4-2 || Bit 38-36 of address.
+
| 0x0 || 0x4 || [[#Map0Tag|Data0]]
 
|-
 
|-
−
| 2 || 27-24 || Bit 35-32 of size.
+
| 0x4 || 0x4 || [[#Map1Tag|Data1]]
 
|-
 
|-
−
| 2 || 31-28 || Bit 35-32 of address.
+
| 0x8 || 0x4 || [[#Map2Tag|Data2]]
 
|}
 
|}
   −
A reply must not use A/B/W, svcReplyAndReceive will return 0xE801.
+
= PointerData =
 +
This is "nn::sf::hipc::detail::HipcFormat::PointerData". This is a 0x8-byte struct.
   −
[[SVC|MemoryAttribute]] IsBorrowed and IsUncached are never allowed for the source address.
+
{| class="wikitable" border="1"
 +
|-
 +
! Offset || Size || Description
 +
|-
 +
| 0x0 || 0x4 || [[#Pointer0Tag|Data0]]
 +
|-
 +
| 0x4 || 0x4 || [[#Pointer1Tag|Data1]]
 +
|}
   −
"Send" means buffer is sent from source process into service process.
+
= ReceiveListData =
 +
{| class="wikitable" border="1"
 +
|-
 +
! Offset || Size || Description
 +
|-
 +
| 0x0 || 0x4 || [[#ReceiveList0Tag|Data0]]
 +
|-
 +
| 0x4 || 0x4 || [[#ReceiveList1Tag|Data1]]
 +
|}
   −
"Receive" means that data is copied from service process into user process.
+
= SpecialData =
 +
{| class="wikitable" border="1"
 +
|-
 +
! Offset || Size || Description
 +
|-
 +
| 0x0 || 0x4 || [[#SpecialTag|SpecialHeaderData]]
 +
|-
 +
| 0x4 || 0x8 || ProcessId
 +
|-
 +
| 0xC || Variable || Array of CopyHandle
 +
|-
 +
| Variable || Variable || Array of MoveHandle
 +
|}
   −
"Exchange" means both "Send" and "Receive".
+
= Header0Tag =
 +
This is "nn::sf::hipc::detail::HipcFormat::Header0Tag". This is a 32-bit flag.
   −
==== Flags ====
+
{| class="wikitable" border="1"
−
Determines what [[SVC|MemoryState]] to use with the mapped memory in the sysmodule.
+
!  Bits
 +
!  Description
 +
|-
 +
| 0-15
 +
| [[#MessageType|MessageType]]
 +
|-
 +
| 16-19
 +
| PointerCount
 +
|-
 +
| 20-23
 +
| SendCount
 +
|-
 +
| 24-27
 +
| ReceiveCount
 +
|-
 +
| 28-31
 +
| ExchangeCount
 +
|}
   −
Used to enforce whether or not device mapping is allowed for src and dst buffers respectively.
+
= Header1Tag =
−
+
This is "nn::sf::hipc::detail::HipcFormat::Header1Tag". This is a 32-bit flag.
−
* Flag0: Device mapping *not* allowed for src or dst.
  −
* Flag1: Device mapping allowed for src and dst.
  −
* Flag3: Device mapping allowed for src but not for dst.
     −
=== Buffer descriptor C "ReceiveList" ===
+
{| class="wikitable" border="1"
−
There's a 4-bit flag in the main header controlling the behavior of C descriptors.
+
!  Bits
 +
!  Description
 +
|-
 +
| 0-9
 +
| RawDataByteSize
 +
|-
 +
| 10-13
 +
| ReceiveListCount
 +
|-
 +
| 13-30
 +
| Reserved
 +
|-
 +
| 31
 +
| HasSpecial
 +
|}
 +
 
 +
= SpecialTag =
 +
This is "nn::sf::hipc::detail::HipcFormat::SpecialTag". This is a 32-bit flag.
 +
 
 +
{| class="wikitable" border="1"
 +
!  Bits
 +
!  Description
 +
|-
 +
| 0
 +
| HasPid
 +
|-
 +
| 1-4
 +
| CopyHandleCount
 +
|-
 +
| 5-8
 +
| MoveHandleCount
 +
|-
 +
| 9-31
 +
| Reserved
 +
|}
 +
 
 +
= Map0Tag =
 +
This is "nn::sf::hipc::detail::HipcFormat::Map0Tag". This is a 32-bit flag.
   −
If it has value 0, the C descriptor functionality is disabled. If it has value 1, there is no C descriptor. If it has value 2, there is a single C descriptor.
+
{| class="wikitable" border="1"
 +
!  Bits
 +
!  Description
 +
|-
 +
| 0-31
 +
| Size (bits 0 to 31)
 +
|}
   −
Otherwise it has (flag-2) C descriptors. Note that flag=2 and flag=3 both encode a single C descriptor.
+
= Map1Tag =
 +
This is "nn::sf::hipc::detail::HipcFormat::Map1Tag". This is a 32-bit flag.
    
{| class="wikitable" border="1"
 
{| class="wikitable" border="1"
−
! Word || Bits || Description
+
! Bits
 +
!  Description
 
|-
 
|-
−
| 0 || || Lower 32-bits of address.
+
| 0-31
 +
| AddressValue (bits 0 to 31)
 +
|}
 +
 
 +
= Map2Tag =
 +
This is "nn::sf::hipc::detail::HipcFormat::Map2Tag". This is a 32-bit flag.
 +
 
 +
{| class="wikitable" border="1"
 +
!  Bits
 +
!  Description
 
|-
 
|-
−
| 1 || 15-0 || Rest of address.
+
| 0-1
 +
| [[#MapTransferAttribute|MapTransferAttribute]]
 
|-
 
|-
−
| 1 || 31-16 || Size
+
| 2-4
 +
| AddressValue (bits 36 to 38)
 +
|-
 +
| 5-23
 +
| Reserved
 +
|-
 +
| 24-27
 +
| Size (bits 32 to 35)
 +
|-
 +
| 28-31
 +
| AddressValue (bits 32 to 35)
 
|}
 
|}
   −
=== IPC buffers ===
+
= Pointer0Tag =
−
Buffer descriptor A/B/... map memory into the sysmodule process. For the mapped memory in the sysmodule the permissions are: desc-A = R--, desc-B = RW-. The buffer is automatically unmapped while the kernel handles the cmdreply, the sysmodule doesn't need to specify anything in the cmdreply to trigger this.
+
This is "nn::sf::hipc::detail::HipcFormat::Pointer0Tag". This is a 32-bit flag.
   −
This memory is mapped in the sysmodule to the same vaddr from the original user-process cmd-request, except with with bits >=(~28(?)) changed to a different ASLR'd region.
+
{| class="wikitable" border="1"
 +
!  Bits
 +
!  Description
 +
|-
 +
| 0-3
 +
| ReceiveIndex
 +
|-
 +
| 4-5
 +
| Reserved
 +
|-
 +
| 6-8
 +
| AddressValue (bits 36 to 38)
 +
|-
 +
| 9-11
 +
| Reserved
 +
|-
 +
| 12-15
 +
| AddressValue (bits 32 to 35)
 +
|-
 +
| 16-31
 +
| Size
 +
|}
   −
No user-process->sysmodule memcpy is done for outbufs, only sysmodule->user-process.
+
= Pointer1Tag =
 +
This is "nn::sf::hipc::detail::HipcFormat::Pointer1Tag". This is a 32-bit flag.
   −
== Raw data section ==
+
{| class="wikitable" border="1"
 +
!  Bits
 +
!  Description
 +
|-
 +
| 0-31
 +
| AddressValue (bits 0 to 31)
 +
|}
   −
[[File:Ipc msg buffer type a example.png|thumb|An example of an IPC message with a type 0xA buffer in it. Red is headers/descriptors, yellow is padding, and blue is data/buffer lengths. Note that the size of the u16 array for type A lengths is padded to fill up a whole word.]]
+
= ReceiveList0Tag =
 +
This is "nn::sf::hipc::detail::HipcFormat::ReceiveList0Tag". This is a 32-bit flag.
    
{| class="wikitable" border="1"
 
{| class="wikitable" border="1"
−
! Word || Description
+
! Bits
 +
!  Description
 
|-
 
|-
−
| ... || Padding to align to 16 bytes.
+
| 0-31
 +
| AddressValue (bits 0 to 31)
 +
|}
 +
 
 +
= ReceiveList1Tag =
 +
This is "nn::sf::hipc::detail::HipcFormat::ReceiveList1Tag". This is a 32-bit flag.
 +
 
 +
{| class="wikitable" border="1"
 +
!  Bits
 +
!  Description
 
|-
 
|-
−
| ... || If sent to an object domain, a [[#Domain_message|domain message]], otherwise a [[#Data payload|data payload]]
+
| 0-6
 +
| AddressValue (bits 32 to 38)
 
|-
 
|-
−
| ... || Padding
+
| 7-15
 +
| Reserved
 
|-
 
|-
−
| ... || Buffer type 0xA lengths (u16 array)
+
| 16-31
 +
| Size
 
|}
 
|}
   −
The total amount of padding within the raw data section is always 0x10 bytes. This means that if no padding is required before the message, there will be 0x10 bytes of padding after the message (before the buffer type 0xA lengths).
+
= MapTransferAttribute =
 +
{| class="wikitable" border="1"
 +
|-
 +
! Bit
 +
! Description
 +
|-
 +
| 0
 +
| AllowsNonSecure
 +
|-
 +
| 1
 +
| AllowsNonDevice
 +
|}
   −
=== Domain message ===
+
= MessageType =
−
This header is used to wrap up requests sent to domains instead of sessions.
+
This is "nn::sf::hipc::detail::MessageType".
    
{| class="wikitable" border="1"
 
{| class="wikitable" border="1"
−
! Word || Bits || Description
+
! Value
 +
!  Description
 +
|-
 +
| 0 || Invalid
 +
|-
 +
| 1 || InvokeMethod
 
|-
 
|-
−
| 0 || 7-0 || Command. 1=send message, 2=close virtual handle
+
| 2 || Release
 
|-
 
|-
−
| 0 || 31-16 || Length of [[IPC_Marshalling#Data_payload|data payload]] in bytes.
+
| 3 || InvokeManagerMethod
 
|-
 
|-
−
| 1 || || Object ID (from cmd 0 in [[IPC_Marshalling#Control|Control]]).
+
| 4 || Invoke2Method
 
|-
 
|-
−
  | 2
+
| 5 || Invoke2ManagerMethod
−
  |rowspan="2"|
  −
  |rowspan="2"| Padding to align to u64
   
|-
 
|-
−
  | 3
+
| 6 || [5.0.0+] Invoke2MethodWithContext
 
|-
 
|-
−
| 4... || || [[#Data payload|Data payload]]
+
| 7 || [5.0.0+] Invoke2ManagerMethodWithContext
 
|}
 
|}
   −
=== Data payload ===
+
= HipcMessageDataOffsetInfo =
−
 
+
This is "nn::sf::hipc::detail::HipcMessageDataOffsetInfo". This is a 0x28-byte struct.
−
This is an array of u32's, but individual parameters are generally stored as u64's.
      
{| class="wikitable" border="1"
 
{| class="wikitable" border="1"
−
! Word || Description
   
|-
 
|-
−
| 0 || Magic ("SFCI" for requests, "SFCO" for responses) as u64.
+
! Offset || Size || Description
 
|-
 
|-
−
| 2 || Command id as u64 for requests, [[Error_codes|error code]] as u64 for responses.
+
| 0x0 || 0x4 || PidOffset
 
|-
 
|-
−
| 4... || Input parameters or return values
+
| 0x4 || 0x4 || CopyHandleOffset
 +
|-
 +
| 0x8 || 0x4 || MoveHandleOffset
 +
|-
 +
| 0xC || 0x4 || PointerOffset
 +
|-
 +
| 0x10 || 0x4 || SendOffset
 +
|-
 +
| 0x14 || 0x4 || ReceiveOffset
 +
|-
 +
| 0x18 || 0x4 || ExchangeCount
 +
|-
 +
| 0x1C || 0x4 || RawOffset
 +
|-
 +
| 0x20 || 0x4 || ReceiveListOffset
 +
|-
 +
| 0x24 || 0x4 || AllCount
 
|}
 
|}
   −
== Official marshalling code ==
+
= CmifInHeader =
−
The official marshalling function takes an array of (buf_ptr, size) pairs and a type-field for each such pair.
+
This is "nn::sf::cmif::CmifInHeader". This is a 0x10-byte struct.
   −
Bitmask 0x10 seems to indicate null-terminated strings, but that flag is ignored by the marshalling code.
+
[5.0.0+] Version was incremented from 0 to 1.
    
{| class="wikitable" border="1"
 
{| class="wikitable" border="1"
−
! Type Mask || Description || Direction
   
|-
 
|-
−
| 4 + 1 || Creates a A descriptor with flags=0. || In
+
! Offset || Size || Description
 
|-
 
|-
−
| 0x40 + 4 + 1 || Creates a A descriptor with flags=1. || In
+
| 0x0 || 0x4 || Signature ("SFCI")
 
|-
 
|-
−
| 0x80 + 4 + 1 || Creates a A descriptor with flags=3. || In
+
| 0x4 || 0x2 || Version
 
|-
 
|-
−
| 4 + 2 || Creates a B descriptor with flags=0. || Out
+
| 0x6 || 0x2 || Reserved
 
|-
 
|-
−
| 0x40 + 4 + 2 || Creates a B descriptor with flags=1. || Out
+
| 0x8 || 0x4 || MethodId
 +
|-
 +
| 0xC || 0x4 || [5.0.0+] Token ([1.0.0-4.1.0] Reserved)
 +
|}
 +
 
 +
= CmifOutHeader =
 +
This is "nn::sf::cmif::CmifOutHeader". This is a 0x10-byte struct.
 +
 
 +
[14.0.0+] Reserved field at +0xC is now InterfaceId, generated as little endian first four bytes of sha256(<fully qualified interface name>). The version field was not incremented.
 +
 
 +
{| class="wikitable" border="1"
 
|-
 
|-
−
| 0x80 + 4 + 2 || Creates a B descriptor with flags=3. || Out
+
! Offset || Size || Description
 
|-
 
|-
−
| 8 + 1 || Creates an X descriptor || In
+
| 0x0 || 0x4 || Signature ("SFCO")
 
|-
 
|-
−
| 8 + 2 || Creates a C descriptor, and writes the u16 size to an offset into raw data. || Out
+
| 0x4 || 0x2 || Version
 
|-
 
|-
−
| 0x10 + 8 + 2 || Creates a C descriptor || Out
+
| 0x6 || 0x2 || Reserved
 
|-
 
|-
−
| 0x20 + 1 || Creates both an A and X descriptor || In
+
| 0x8 || 0x4 || Result
 
|-
 
|-
−
| 0x20 + 2 || Creates both an B and C descriptor || Out
+
| 0xC || 0x4 || [14.0.0+] InterfaceId ([1.0.0-13.2.1] Reserved)
 
|}
 
|}
   −
C and X (Pointer and ReceiveList) descriptors are backed by the "pointer buffer", a buffer in the service process. Its size is a u16, which is retrieved using the "QueryPointerBufferSize" control message. If the client code determines all buffers with flag 8 do not fit in the pointer buffer, it returns error 0x11A0B.
+
= CmifDomainMessageInHeader =
 +
This is "nn::sf::cmif::detail::CmifDomainMessageInHeader". This is a 0x10-byte struct.
   −
For buffers with flag 0x20 it creates two descriptors (A+X or B+C), but one descriptor is NULL (zero size and pointer), while the other holds the expected values. X/C descriptors are used as the non-NULL descriptor where possible, but if they don't fit in the pointer buffer, A/B descriptors are used instead. The code defers processing of type 0x20 buffers with sizes that fit in a u16 (and may therefore fit in the pointer buffer). This ensures all type 8 buffers get pointer-buffer space before any type 0x20.
+
{| class="wikitable" border="1"
 +
|-
 +
! Offset || Size || Description
 +
|-
 +
| 0x0 || 0x1 || [[#RequestKind|RequestKind]]
 +
|-
 +
| 0x1 || 0x1 || InObjectCount
 +
|-
 +
| 0x2 || 0x2 || InRawSize
 +
|-
 +
| 0x4 || 0x4 || [[#CmifDomainObjectId|TargetObjectId]]
 +
|-
 +
| 0x8 || 0x4 || Reserved
 +
|-
 +
| 0xC || 0x4 || [5.0.0+] Token ([1.0.0-4.1.0] Reserved)
 +
|}
   −
(The order in which the deferred type 0x20 buffers are processed is determined by a convoluted loop.)
+
= CmifDomainMessageOutHeader =
 +
This is "nn::sf::cmif::detail::CmifDomainMessageOutHeader". This is a 0x10-byte struct.
   −
== Official IPC Cmd Structure ==
+
{| class="wikitable" border="1"
−
Official struct that is stored for each IPC command. It contains precalculated offsets for different portions of the command structure.
+
|-
 +
! Offset || Size || Description
 +
|-
 +
| 0x0 || 0x4 || OutObjectCount
 +
|-
 +
| 0x4 || 0xC || Reserved
 +
|}
   −
All offsets are given is in number of u32 words.
+
= CmifDomainObjectId =
 +
This is "nn::sf::cmif::CmifDomainObjectId". This is a 4 byte value.
   −
struct IpcCmdStruct {
+
= BufferAttribute =
−
  u8  unk0;
+
This is "nn::sf::cmif::BufferAttribute".
−
  u8  has_handle_descriptor;
  −
  u8  pad0[2];
  −
  u32 cmd0;
  −
  u32 cmd1;
  −
  u32 offset_handle_descriptor;
  −
  u32 pad1;
  −
  u32 offset_handles;         
  −
  u32 pad2;
  −
  u32 offset_x_descriptors;
  −
  u32 offset_a_descriptors;
  −
  u32 offset_b_descriptors;
  −
  u32 offset_w_descriptors; /* this is a guess */
  −
  u32 offset_raw_data;
  −
  u32 offset_c_descriptors;
  −
  u32 unk2;
  −
  u32 unk3;
  −
}
  −
 
  −
== Control ==
  −
When type == 5 you are talking to the IPC manager. These are processed by the sysmodule.
      
{| class="wikitable" border="1"
 
{| class="wikitable" border="1"
 +
!  Value
 +
!  Description
 +
|-
 +
| 0x0 || None
 +
|-
 +
| 0x1 || In
 +
|-
 +
| 0x2 || Out
 +
|-
 +
| 0x4 || HipcMapAlias
 +
|-
 +
| 0x8 || HipcPointer
 
|-
 
|-
−
! Cmd || Name || Arguments || Output
+
| 0x10 || FixedSize
 
|-
 
|-
−
| 0 || ConvertSessionToDomain || None ||  
+
| 0x20 || HipcAutoSelect
 
|-
 
|-
−
| 1 || ConvertDomainToSession || u32 domain ||  
+
| 0x40 || HipcMapTransferAllowsNonSecure
 +
|-
 +
| 0x80 || HipcMapTransferAllowsNonDevice
 +
|}
 +
 
 +
= RequestKind =
 +
{| class="wikitable" border="1"
 +
!  Value
 +
!  Description
 
|-
 
|-
−
| 2 || DuplicateSession || None ||  
+
| 0 || Invalid
 
|-
 
|-
−
| 3 || QueryPointerBufferSize || None || u32 as u16-size
+
| 1 || Send
 
|-
 
|-
−
| 4 || DuplicateSessionEx || u32 unknown ||  
+
| 2 || Close
 
|}
 
|}
Retrieved from "https://switchbrew.org/wiki/Special:MobileDiff/2892...12597"